l was quoted £6k for the entire ute... after careful consideration & some homework l can do it myself (using a barn to avoid rain/dust in the process) for around £700...that includes buying a 80psi compressor.
What have you done to your Land Cruiser this week? (74 Viewers)
- Thread starter IH8MUD
- Start date
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.
Last week l sanded, wire brushed and began grinding/treating the rust areas on the inside of the utes bed in preparation for a complete rust coating & raptor finish. l also attempted to strip the bumper for prep & re-spraying which after 5 coates of a fairly acidic paint remover (Nitro-mores) didn't even blister..so the 1-2mm of 'enameled' paint is going to need grinding off... fun times.
The week before.... l replaced the handbrake set up (again)..after finding the 'new' shoe retaining pin had spat its horseshoe retainer off & both had dropped down into the bottom of the brake drum leaving me with no handbrake. the 2 original hardened pins were fine, seems there's a lack of height/width on the new pin & the steel material used to make the shoes is soft, as the shoe pin eye had elongated causing the pin to slide/move excessively to the point the horseshoe clip was spat off...(sent an email raising the issue to my supplier with no reply as yet).
This coming week, it seems as of 10am l have a diesel leak ( or maybe the vanilla scent is deluding my senses).. anyway the ute's began to play up at start up on friday..turns over but won't start, (l had a fuel filter light flickering at idle & thought l'd change the fuel filter (old 1 had done 20k - 1yr old)..then l decided to remove/clean/check the sedimenter... it came off fine, had some crap in the base & the float was sticky, so cleaned it all up, checked it..refitted it, bled the system & the lights still coming on. Right now l'll live with it...in the meantime l'll be hunting down whether its drawing in air...l bled it on Friday & it started/ran fine over the weekend....
Here's a question for you.... my earth lead (which l previously removed/cleaned & refitted, l also cleaned the engine connection) has a grey/red crust appearing... which it didn't have before..any thoughts ?.
The week before.... l replaced the handbrake set up (again)..after finding the 'new' shoe retaining pin had spat its horseshoe retainer off & both had dropped down into the bottom of the brake drum leaving me with no handbrake. the 2 original hardened pins were fine, seems there's a lack of height/width on the new pin & the steel material used to make the shoes is soft, as the shoe pin eye had elongated causing the pin to slide/move excessively to the point the horseshoe clip was spat off...(sent an email raising the issue to my supplier with no reply as yet).
This coming week, it seems as of 10am l have a diesel leak ( or maybe the vanilla scent is deluding my senses).. anyway the ute's began to play up at start up on friday..turns over but won't start, (l had a fuel filter light flickering at idle & thought l'd change the fuel filter (old 1 had done 20k - 1yr old)..then l decided to remove/clean/check the sedimenter... it came off fine, had some crap in the base & the float was sticky, so cleaned it all up, checked it..refitted it, bled the system & the lights still coming on. Right now l'll live with it...in the meantime l'll be hunting down whether its drawing in air...l bled it on Friday & it started/ran fine over the weekend....
Here's a question for you.... my earth lead (which l previously removed/cleaned & refitted, l also cleaned the engine connection) has a grey/red crust appearing... which it didn't have before..any thoughts ?.
I really like the battery terminal corrosion protection spray I got from NAPA years back.
This is what they sell now https://www.autozone.com/miscellane...tector-spray/p/crc-battery-terminal-protector. I would clean both surfaces again and then spray them, let dry, assemble and then spray again.
This is what they sell now https://www.autozone.com/miscellane...tector-spray/p/crc-battery-terminal-protector. I would clean both surfaces again and then spray them, let dry, assemble and then spray again.
6f40j9
SILVER Star
How many times can I spam my running board project?
Huge job modified vw wing window opener holder thing off Etsy work lol
Happy memorial grateful for all who have sacrificed for our country
Happy memorial grateful for all who have sacrificed for our country
Last edited:
sleepycruiser
I will get by….I will survive -Touch of Grey LC200
Put in a fusible link I ordered from @Coolerman
Also was able to replace the original socket as the old one was broken. Easy to swap out…I did have to drill new holes on the socket to align with the firewall holes. Additional details/measurements in my thread.
Also was able to replace the original socket as the old one was broken. Easy to swap out…I did have to drill new holes on the socket to align with the firewall holes. Additional details/measurements in my thread.
l'll give it a try thanks Charlie...
brian
SILVER Star
Washed it.
Living under/around maples it gets covered in the black sooty mold.
Living under/around maples it gets covered in the black sooty mold.
I did the same thing and it took off and on several weeks. Air compressor couldn't keep up, sand blaster was leaking, sweating my a$$ off (Las Vegas in the summer). Definitely would have been nice to pay someone to do it, but was nice once it was done.
Catching Neutral
GOLD Star
I am definitely partial to the darker color.
Looks great.
Catching Neutral
GOLD Star
They always doWife and I went to Mission Impossible...no spoilers, but there's a scene with two vintage Land Cruisers...and the bad guys drive Jeeps.
Repainted bumpers and bumperettes: (before/after)
Oh and new shoes! Thank goodness!
Oh and new shoes! Thank goodness!
Last edited:
Roof fiberglass, paint, drip rail rust repair & headliner is next!
sleepycruiser
I will get by….I will survive -Touch of Grey LC200
Bought the seats recently from @clrussell
I wanted to repaint the backs. When I took them off I realized it still had the surround leather on it. Not really an easy way to clean it and reattach so I bought some edge trim..luckily I bought the exact correct fit. Goes on easily, bends around the corners and is pushed in firm so it will never come off by itself. New rear covers and headliner on order.
I painted the backs the same color as my wheels and rear seat frames. Front seat frames will get painted as well. Rustoleum Farm and Implememt Massey Ferguson Grey
I wanted to repaint the backs. When I took them off I realized it still had the surround leather on it. Not really an easy way to clean it and reattach so I bought some edge trim..luckily I bought the exact correct fit. Goes on easily, bends around the corners and is pushed in firm so it will never come off by itself. New rear covers and headliner on order.
I painted the backs the same color as my wheels and rear seat frames. Front seat frames will get painted as well. Rustoleum Farm and Implememt Massey Ferguson Grey
Buffchief
SILVER Star
Took the top apart for work and installed all new rivets and self level seam sealer
And painted a bezel! Don’t sell yourself short.
Well done. I do not look forward to this project on mine
I like the trim on the seat backs.
Buffchief
SILVER Star
It is a bit time consuming! Take your time on one section at a time. Grainger has the solid dome top rivets. Waiting for my inside roof covering and about to paint the top.
pb4ugo
SILVER Star
My scout p/s steering box started leaking out the steering shaft input seal. I figured it was time rebuild/reseal it. So far, no more leaking.
