What have you done to your Land Cruiser this week? (72 Viewers)

[77mustard40]

Swapped Bilsteins for the 10 year old OME’s this evening, much smoother on the road. We will see on dirt.

 

[orangeyz]

Started the motor today

 

[JayDoc]

Restored the front turn signals. New OEM lenses and gasket. Very happy with the results.
View attachment 2371880View attachment 2371882View attachment 2371883

Who did you get your lamp lenses from?
Thanks.

 

[Advrider639]

Trail ride last weekend, she preformed 100%

 

[KRGfab]

Spent some time replacing all the rear brake lines. Tomorrow are the fronts and clutch lines.

 

[bikersmurf]

Steering is done. Consist of:
• HJ61 steering box/arm
• BJ75 streering rod w/BJ75 left side steering rod end, on the right side is BJ42 left tie rod end
• original BJ42 tie rod, right side TRE’s hole is reamed a little bit
• Monroe SC-2915 steering stabilizer, mounting hardware (conical pins) is taken from Monroe SC-2946
• homemade shock tower (60 mm further back)
View attachment 2369705

Is there a write up on using the BJ75 rod and rod end a BJ42 TRE? What’s the total length?

I’m gathering what I need to convert to P/S with a Scout II Saginaw box which will need almost exactly the same rod. I’d prefer to use parts that can be ordered over custom fabricated parts.

 

[thecrazygreek]

Just starting to feel better coming off of Coronavirus....

Managed to get a couple stickers stuck, and did some cleaning on the 64.

 

[DSB345]

Beautiful work! Glad to hear your doing well.

Just starting to feel better coming off of Coronavirus....

Managed to get a couple stickers stuck, and did some cleaning on the 64.



View attachment 2375343

 

[-MaTTi-]

Is there a write up on using the BJ75 rod and rod end a BJ42 TRE? What’s the total length?

I’m gathering what I need to convert to P/S with a Scout II Saginaw box which will need almost exactly the same rod. I’d prefer to use parts that can be ordered over custom fabricated parts.

Here is some: FJ60 Power Steering Conversion for FJ40 while keeping air pump

Fj60 power steering need info on drag link pitman arm setup

forum.ih8mud.com

Mine is now 95 cm (pin to pin). It can be adjusted between ca. 91-99 cm.

 

[JKIII FJ40]

Took my old girl out for a weekend drive,View attachment 2354938View attachment 2354940View attachment 2354941

what color is your rig?

 

[Krenie]

Got my headers back from Jet-Hot and mounted them.

 

[TRAIL TAILOR]

New design for the 40 rear bumper. Front to come. Will be available with or without arms and come with 3 way led lights (same lights that KayMar uses)

Top two in the picture.

 

[Jdc1]

New design for the 40 rear bumper. Front to come. Will be available with or without arms and come with 3 way led lights (same lights that KayMar uses)

Top two in the picture.

View attachment 2376288View attachment 2376289

You couldn’t stay away from the 40 section.....

 

[TRAIL TAILOR]

You couldn’t stay away from the 40 section.....

J,

Well since I have 3 - 40 series LS3 swaps/ 1 frame off and 2 - 55 builds going on in the shop right now.... might as well right!

J

 

[Dizzy]

Two AGM batteries for scootersand wheelchairs, jumper cables, 5/64" 6013 electrodes.

 

[thecrazygreek]

Tic tock...

 

[cruiserboy14]

Got a new high vis sticker thanks to a co worker, and tinkered in the engine bay.. it hard to do to much in the Arizona heat...

 

[Trigger6]

A productive weekend... 1) Replaced the leaking manifold gasket (small exhaust leak on the #1 cylinder exhaust where the gasket had cracked on the outer edge... replaced using OEM ‘yota gasket). 2) Replaced the weatherstripping on all 4 doors.

Took the wife for a drive, “It doesnt sound like a rattle trap anymore...”. But now I’m getting worried that she’s going to want to drive it all the time...

 

[Catching Neutral]

Accomplished so much today. See “ Iron Yak“ thread. Then took the Iron Yak for a victory lap.. Felt great to be behind the wheel again.

 

[Catching Neutral]

I should add that SMGs hood pins are AWESOME