What Did You Do with Your 80 This Weekend? (47 Viewers)
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.
I wish that did work but it didn't shine through unfortunately. Its actually silver>copper>glass The LEDS would show through the copper but I didn't know how to remove the silver without removing the copper too so I just went to the glass. I was thinking of a cellphone mirror film but unless it gets too annoying its fine for now.
Installed my Slee and Engo 10k !
Spent a lot of quality truck time.... finished off the armour and sold the ARB to a local owner..... added a pair of Hella 4000's and am wiating on Slee's dual battery kit so I cna wire up all the fun stuff....
I also dicided to add rubber shelf liner and some carpet scraps to the cupholders, and console ans well jsut liner in the glove.... the two layers reeally make things not rattle....
Need to get my darn post coutn up so I can post pics !
Spent a lot of quality truck time.... finished off the armour and sold the ARB to a local owner..... added a pair of Hella 4000's and am wiating on Slee's dual battery kit so I cna wire up all the fun stuff....
I also dicided to add rubber shelf liner and some carpet scraps to the cupholders, and console ans well jsut liner in the glove.... the two layers reeally make things not rattle....
Need to get my darn post coutn up so I can post pics !
Aggiesdm
***** Regular
Got that dang little steering shaft rubber boot replaced at the firewall, and finally straightened my steering wheel while I was there. The boot was a little worn and it felt like my heater was on all the time. Fixed now!
Getting here ready for deer hunting this weekend! Hopefully they'll be a few more blood stains in the back upon my return!
Getting here ready for deer hunting this weekend! Hopefully they'll be a few more blood stains in the back upon my return!
the LX got to take its first long trip - probably the highest and coldest it has ever been (truck lived in TX before AZ)
Last edited:
How's that 4bt treating ya? I had those yokes years ago, good tire but wore fast on the street. Good luck!
Ammo
Yay!
Yay!
"it's only gonna feel funny now . . . " Steve Watson (of King-of-the-Hammers fame)
I repeat that to myself every time I hit ruts like that
Hey Cody do you have a write up or pics on the rear bumper ends?? im looking into "adding on" to the rear bumper and getting rid of the plastic thanks!
Some new meats and front bumper build and flexed out on a zr1 blazer
I’ve had my Nitro Gear 4.88’s for about a month and finally got around to doing the install. I’m not done yet, a couple more evenings and it should be buttoned up.
I’ve completed the rear third member and I have to say the gears set up great and had a good pattern with all the factory bearing shims which is nice because then you have one thick ridged shim instead of stacking thin ones. All in all I’m very impressed with the quality and ease of set up with “Nitro Gear”
I also need to give a big thanks to Yotamasters.
One of the special OE ring gear T-bolts and nut was gauled on disassembly. None of the Toyota dealers for 50 miles had one and it was going to be 4 day on special order. Eric at Yotamasters had them and came down to the shop on Saturday to get me one. Those guys are great. I also got my knuckle overhaul kit and wheel bearings from them.
I will also be trying some offset kingpin bearings in the knuckle that give an additional 2.5deg. of castor in addition to whatever radius arm stuff you’ve done. I think there will be a slight tie rod to radius arm interference though, as I already have bushings installed. I will post up my findings when I get there. It definitely needs more castor though so I hope it works.
I’ve completed the rear third member and I have to say the gears set up great and had a good pattern with all the factory bearing shims which is nice because then you have one thick ridged shim instead of stacking thin ones. All in all I’m very impressed with the quality and ease of set up with “Nitro Gear”
I also need to give a big thanks to Yotamasters.
One of the special OE ring gear T-bolts and nut was gauled on disassembly. None of the Toyota dealers for 50 miles had one and it was going to be 4 day on special order. Eric at Yotamasters had them and came down to the shop on Saturday to get me one. Those guys are great. I also got my knuckle overhaul kit and wheel bearings from them.
I will also be trying some offset kingpin bearings in the knuckle that give an additional 2.5deg. of castor in addition to whatever radius arm stuff you’ve done. I think there will be a slight tie rod to radius arm interference though, as I already have bushings installed. I will post up my findings when I get there. It definitely needs more castor though so I hope it works.
Last edited:
I hung up my new Christmas Tree ornament from musthave really cool.
That's the coolest $7 I ever spent!
That's the coolest $7 I ever spent!
That picture didn't work, try this.
Didn't want to spend $1, 450 for a local paint job , fortunately I live at the border , went across and found a guy willing to paint my lc for $600 :O !!! I luv the color and can't wait to have it back (the bad side , he still have the lc after TWO weeks , we had bad weather a couple of days , but two weeks , cmon man ....crazy)
Polar Bear
Is it supposed to sound like that?
Nothing like a south of the border bomb can job!
Installed new plugs and wires
Wires were over 5 years old and still looked new
Wires were over 5 years old and still looked new
Probably had it painted in two days and has been "enjoying" the fruit's of his labour since.
Tapage
Club 4X4 Panamá
Add a Koso water temp digital gauge to my dash ..
impress how fresh it's running my 1HD-T
impress how fresh it's running my 1HD-T
