Builds The KY40 - Tilda Bogue Service Station
- Thread starter wngrog
- Start date
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.
- Thread starter
- #122
Black cap (G-Cat whispered to himself knowing that Nolaeioun has a plan).
That may have to be a local thing later. We shall see. He wants it addressed.
- Thread starter
- #123
One thing I can say super positive is the rust free condition of the top. All the bolts went in smooth as well. Overland Metric
New calipers and pads
Seat belt planet belts
New calipers and pads
Seat belt planet belts
- Thread starter
- #124
Funny. I just spent the last hour filling in all of the holes the previous jackass drilled in the tub with bolts. Used some 3m dum dum to get a few cracks filled. Should stay pretty dry.
- Thread starter
- #125
Late start today.
I started off removing the backwards wing window
I bought a whole door that had a good drivers wing window but I freaking snapped the rod off. Gonna have to get the Wizard to put the good one on the red frame
The rear handle was broken. I bought this one out of Indonesia. What a pain in the ass it is to replace this thing
I started off removing the backwards wing window
I bought a whole door that had a good drivers wing window but I freaking snapped the rod off. Gonna have to get the Wizard to put the good one on the red frame
The rear handle was broken. I bought this one out of Indonesia. What a pain in the ass it is to replace this thing
- Thread starter
- #126
Yesterday the Wizard came up and fixed the wing window.
I got the correct flange for this 78 shaft I had in the house. His driveshaft was a bit too long. I think the springs he had were the ones that push the axle back at rest in the middle of the fender well
Got this email ....
I got the correct flange for this 78 shaft I had in the house. His driveshaft was a bit too long. I think the springs he had were the ones that push the axle back at rest in the middle of the fender well
Got this email ....
- Thread starter
- #127
Check it.....
33x9.50-15 Kenda Klever looks perfect
33x9.50-15 Kenda Klever looks perfect
85roktoy
SILVER Star
WarDamnEagle
SILVER Star
Nice. I'm leaning heavily toward those for my pig.
- Thread starter
- #130
The new old stock Aisan carb made it back from Jim and I wasted no time getting it on and hooked up
- Thread starter
- #131
I got the choke, throttle and vacuum line in then set the timing.
Tomorrow we are going to figure out a good way to secure this FJ55 air cleaner off to the side of the PS res
Tomorrow we are going to figure out a good way to secure this FJ55 air cleaner off to the side of the PS res
If you are comfortable with popping those head bolts, sectioning/extending/modding a stock F bracket would be the cleanest looking. I’m on the fence about securing to the fender.
- Thread starter
- #133
It's too far away.
I would not go to the fender because the motor moves and the fender won't.
I'm going to make a bracket off the two bolts on the intake manifold
PS pump bracket have any available mounting points?
- Thread starter
- #135
Nope.
Manifolds have a tough time as it is staying tight IMHO. I'd do the head bolts bracket
- Thread starter
- #137
It will be a hard mount somewhere with a soft mount under the canister since it's more or less resting on the fender.
We will figure out something. I'm not crazy about trying to go to the head. It's a long way over to it. Maybe to the Saginaw bracket itself.
We will figure out something. I'm not crazy about trying to go to the head. It's a long way over to it. Maybe to the Saginaw bracket itself.
Oh wow! you find a project to use this carburetor!!
You want more?
You want more?
Where can I find the rear swing out?
