WarDamnEagle

That bolt on the parts diagram I looked at for my 75 didn’t have the cover.

I don't think they are oem as I never seen those before . Toyota uses caps on the frp bolts in the rear and they look different . You might want to upgrade to the early nob style bolts to secure the windshield frame they are supercool

If you have a lift cylinder that has down pressure, yeah. Most Hyster style forklift lift cylinders lower by gravity, so no.

Local trade school surplus mechanical training station. 20 plates covered in gears, pulleys, shafts, collars, couplers, bearings, etc, etc. Plates store on front/back/sides/underneath. Bigger/heavier gears etc shown but box full of smaller stuff...

All you should really need is the pin, not the shackle.

Another resource is to ship your 3rd to Zuk. He freshened up my rear 3rd with ARB few years back. I wanted all new bearings, and new set of 4.56 R&P at the same time. The previous pinion bearing race spun on the pinion shaft so that made that...

Electricity has been installed, and the doors are going on. New supervisor showed up on the job site. What a stickler...

I'll have send you guys some of my accounting pencils with the eraser on the end. 👍

I hear you. I was close until I had the seat belts refurbished. 😂

Thanks man! Yeah, creeping up to that $5k with a margin so thin you can barely force an 0.012” feeler gauge in between.

Sliders on my 85 4Runner are welded on. Much less complicated, cleaner, but a tad bit harder to move or remove. 😁

Part number for that one is 65896-90K00. Just FYI

Same hitch with dimension diagram. Don’t think it will work. https://www.reesehitches.com/sp-874ch-folding-assist-step.html?srsltid=AfmBOoq87bSMKCzbWfYZN_nEF3mxXDnPmtlFqbBaGSGRak4dEtIuhIzG

Thanks sir! I wish I still had it. They are so nice for trips compared to a 40. Some of those 2UZ pigs are really temping! You are doing amazing work on your pig. Will be awesome when done. Completely jealous you did all this on $5k.

If you have a bender you could always do something like this. Frame mounted, removable and provide a nice place to stand on to reach the roof.

Front fenders and frame mounted sliders. My front fenders were trimmed and set up for the tub mounted sliders that were on there for a long time. “Capping” the rockers and going with frame mounted sliders is going to require them getting...

Whole damn thing. Hangers get powder.

Found this in a drawer the other day. I can not remember what 40 it came with, I have had soo many...

frame off to blast and powder. exhaust gets cerakote. steering box got sent for a rebuild, too.

Just got my 71 back from the windshield replacement shop The glass was supplied by a national supplier FYG. $169 to the windshield installer. He got it in 3 days. Ordered two to make sure at least one was not scratched. Sent the other on back...

You’re killin’ me, smalls! How about after we get to the part where it’s been to a couple Pig Parties and I’ve actually got to drive it for a while?

Hey siri: what is bobm trying to say? Siri: you should wipe your phone now before you are put on a watch list and stay out of the 55 section.

Mostly true to 100% true depending on the store and or the employee you are dealing with at that moment... The store has the option of having you sign an affidavit self-certifying that you are the owner of the bottle and I've had to do that when...

Great news, Ford Explorer brakes pass the fit test.

I bought a smaller bottle that I could afford when first starting. Then throughout succeeding exchanges picked up the increasingly larger sizes for the price difference and cost of gas.