Spending time think about how to make a cup holder for my coffee (alcohol) & where best to place it. No actual work just thinking
What have you done to your Land Cruiser this week? (44 Viewers)
- Thread starter IH8MUD
- Start date
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.
Michael B
SILVER Star
YOUR RIG LOOKS GOOD!!!!!
Michael B
SILVER Star
Thanks!
- Joined
- Apr 14, 2004
- Threads
- 1,472
- Messages
- 36,795
- Location
- 818-953-9230
- Website
- www.marksoffroad.net
View attachment 1391417 View attachment 1391418 View attachment 1391419 Hey @fjgoober I finally installed the last of your handy work today! Along with a few other pieces.
I haven't followed your build. What's up with the transmission floorshift boot? Alternate transmission?
Michael B
SILVER Star
Yes Mark I have an H55F w/split case installed.
Put my hard doors back on after some sound deadening installed, cleaned up all internal components, new door seals and stoked! Also installed Racer's LED headlights. And a rear LED light bar.
View attachment 1392055 View attachment 1392056 View attachment 1392055 View attachment 1392055 View attachment 1392056
View attachment 1392055 View attachment 1392056 View attachment 1392055 View attachment 1392055 View attachment 1392056
Last edited:
78fj40mg
TLCA #23510
Beautiful FST and hard doors!! Nice work!
A labor of love!
Rebuilt the Fuel pressure regulator, throttle body gaskets & fuel pump. Pulled it out of the garage and washed it. Then finally took it for a drive.
Beautiful! One of my favorite trucks ! Hoping to see you you in April at the swap meet.
Sounds good!!
Vossie
#thecrazycruiserman
nice. love the head lights and light bar. did the headlights just fit straight in? any mods to wiring?
@Lazman looks great. Any details on that rack you have on your 40?
Edit: Found the thread. FJ/BJ40 Soft Top Roof Rack Pics
Edit: Found the thread. FJ/BJ40 Soft Top Roof Rack Pics
Head lights mounted right in without any mods. I did buy new adjustment grommet and screws just to update. Took about 30 min from start to finish. These put off an amazing beam.
Info on the headlights please, I would like to do the same to mine. Price, where to buy?
PM sent
Lost the 'old tub to new doors' striker plates I 'd gotten from Domsmith, (Thanks!!), then found them again, so , before I can lose them again, I started on that task. Warm day here for winter, nice enough in an unheated barn to work. Here's a link to his thread:
Custom door strikers- late doors to early tub
Test fitting the first plate before welding up the hoop, found the replacement screws that came with the late model hoops were too long, bottomed out in the body..
I do have two older screws so I went to put them in, first screw worked perfectly,
Then I couldn't find the other one...it was right there a second ago, didn't remember dropping it, but hey, cement floor, shouldn't be hard to find. Couldn't find it anywhere. On hands and knees with a flashlight, inside and under, sifting thru straw, getting madder and madder ...unbelievable! Over and over , up and down, inside and out, empty pockets....a couple of times. No joy.
Found it,
stuck to the magnetic clip on the back of the flashlight that I was using the whole time.
Custom door strikers- late doors to early tub
Test fitting the first plate before welding up the hoop, found the replacement screws that came with the late model hoops were too long, bottomed out in the body..
I do have two older screws so I went to put them in, first screw worked perfectly,
Then I couldn't find the other one...it was right there a second ago, didn't remember dropping it, but hey, cement floor, shouldn't be hard to find. Couldn't find it anywhere. On hands and knees with a flashlight, inside and under, sifting thru straw, getting madder and madder ...unbelievable! Over and over , up and down, inside and out, empty pockets....a couple of times. No joy.
Found it,
stuck to the magnetic clip on the back of the flashlight that I was using the whole time.
