Freds40 builds a 60 (1 Viewer)

[freds40]

Just looked @ his site and it dosn't look too promising. Did you try Now serving ? It's been a couple of months since I got mine from him. I've heard he is a 1 man shop and does this on the side from his full time job.

BTW, for the sake of ease of install and time, I threw my clutch fan and shroud in so I can get it running and wheel it a bit. After I've driven it a while, I'll throw the Taurus fan and DCcontrol in.

 

[dtrain]

Just looked @ his site and it dosn't look too promising. Did you try Now serving ? It's been a couple of months since I got mine from him. I've heard he is a 1 man shop and does this on the side from his full time job.

BTW, for the sake of ease of install and time, I threw my clutch fan and shroud in so I can get it running and wheel it a bit. After I've driven it a while, I'll throw the Taurus fan and DCcontrol in.

I will take a look there. I've heard his stuff is great and does exactly what I need but the reviews are mixed. Sounds like he delivers but it takes a while.

Truck looks good!

 

[freds40]

Thanks.

 

[freds40]

It's running!

Of course it sounds like azzzzzzzzzzz with no exhaust past the manifold but it is indeed running.

Hopefully get the exhaust done beginning of next week and cruise this thing.

 

[D'Animal]

Congrats!

It's running!

Of course it sounds like azzzzzzzzzzz with no exhaust past the manifold but it is indeed running.

Hopefully get the exhaust done beginning of next week and cruise this thing.

 

[brokenparts]

Keep it up man... it looks great!

 

[Moby]

After I've driven it a while, I'll throw the Taurus fan and DCcontrol in.

I will be very interested to see if you get that Taurus fan to fit. I've got a new one just lying around and I'm looking for more cfm than my Contour fan pulls (which is more than adequate 98% of the time but I recently found the 2%). However I'm having trouble seeing the depth of the Taurus fan fitting with the water pump snout. Of course I've got a 62 with the tranny cooler which it limits where I can position the center of the fan...

 

[freds40]

I threw the Taurus fan in and it will fit. THe fan motor is off center and if I turn the whole shroud upside down, the motor sits off to the passenger side of the water pump pulley. Should be pretty easy when I go to do it. Just a little more time consuming than I need right now.

 

[911SMIL]

You have a sponge on your antenna... (Teach you not to be home when I come by)




Call me when you get a free minute...



Chris

 

[freds40]

Funny thing is when I pulled into the driveway I said to Amanda, I bet it was Chris!

 

[weak-link]

Done yet?

P.S. you suck at updates and pictures

 

[freds40]

What's to update? It's still in the garage.

 

[weak-link]

the third that grew hair

 

[freds40]

Carved up the front fenders so I could turn the tires.

And took it for a spin around the block today. There is still quite a bit to do and there were a few issues to tend to but it's definately getting closer.

1 more.

 

[weak-link]

90301-64002 is the o ring just below the plate and it should be around 2bucks

web site i was telling you about https://www.1sttoyotaparts.com/

 

[freds40]

Just ran by Bingham and picked up the o-ring and the seal. The seal was a bit worn when I was in the box so I figure I'll change it while I'm back into it. Should both be in Friday morning.

 

[brokenparts]

I like the look of no front bumper.

If you get a chance would you mind measuring from the ground to the bottom of your frame rail? Yours looks lower than mine did with the 39.5s.

 

[freds40]

Right now the frame to ground is right @ 24.5". My guess is that will drop an inch or 2 once I get it out and work the springs a bit.

 

[brokenparts]

nice work... mine was about 28-29" at first. It dropped to 26ish when the springs settled and I thought the balance wasn't too bad and the pucker factor was at least predictable using the stock springs. I ran 2" spacers in the front and 1.5 in the back.

 

[Mace]