Cruiser Cult
Supporting Vendor
Nice work!
What have you done to your Land Cruiser this week? (21 Viewers)
- Thread starter IH8MUD
- Start date
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.
What color code did you use? How did you paint it?
Hi Serg! I used cruiser corps paint - I did a little Post in thread 'Freeborn Red 309 Aerosol Spray Can Review?'
Freeborn Red 309 Aerosol Spray Can Review? - https://forum.ih8mud.com/threads/freeborn-red-309-aerosol-spray-can-review.1295005/post-14732417
Thank you all!
I have ordered two cans from them. Want to use them on the floor (only in front). Just want to see how they will differ from the original red. It looks really nice. Thanks to post it.
Last edited:
69FJ40:
Removed the fender to facilitate installing rebuilt steering box. I knew the PO didn’t disassemble to paint but wasn’t expecting this. And now I can clearly see the brake master is leaking. More of the same.
Removed the fender to facilitate installing rebuilt steering box. I knew the PO didn’t disassemble to paint but wasn’t expecting this. And now I can clearly see the brake master is leaking. More of the same.
Added some 4 degree caster shims from @orangefj45 to my 40 a few nights ago (has OME springs and shackles) to improve handling after seeing @wngrog install them on his builds. Steering was a little squirrelly before but not too bad, amazed at how much better it is now though - one of those things I didn’t know I even needed and now couldn’t go without. Very pleased!
We really need to get the Columbus 40s together this spring/summer.
orangefj45
Supporting Vendor
Very cool!
Glad the shims made a noticeable improvement, they typically do.
Appreciate you sending business our way. Please keep us in mind if you need anything else.
Happy New year!!!!
Georg @ Valley Hybrids @ Cruiser Brothers
Count me in. I’m NE by the reservoir.
I was driving the other day and my clutch dropped to the floor. I managed to get it home and after pressing the clutch in the garage, my garage floor was covered in brake fluid.
I ended up replacing the Clutch Master Cylinder and Slave Cylinder, but the real problem was a bent spring.
I got it up and running today and was happy to enjoy this unseasonably warm New England day in the 40.
I ended up replacing the Clutch Master Cylinder and Slave Cylinder, but the real problem was a bent spring.
I got it up and running today and was happy to enjoy this unseasonably warm New England day in the 40.
Tune up in a can. It's a big can though.
I've had pinging problems for months now. Been retarding the timing to the point it was almost undriveable at idle. Looked at my plugs and decided that carbon build-up might be the problem. Been dribbling this stuff down the carb for a few weeks now. 4 or 5 or 6 times a day, let it die wet, let it sit a bit. Start it up and warm it up and let it smoke a lot.
Must be working, can run the timing at 22 BTDC now with it almost starting to ping.
I've had pinging problems for months now. Been retarding the timing to the point it was almost undriveable at idle. Looked at my plugs and decided that carbon build-up might be the problem. Been dribbling this stuff down the carb for a few weeks now. 4 or 5 or 6 times a day, let it die wet, let it sit a bit. Start it up and warm it up and let it smoke a lot.
Must be working, can run the timing at 22 BTDC now with it almost starting to ping.
Ackcruisers
SILVER Star
Changed oil sending unit to OEM Toyota 83520-55011 and got baseline reading with mechanical gauge for peace of mind (60 psi at cold start running Rotella 15W-40, 30 psi at idle at operating temp). Replaced door latch with OEM Toyota 69310-90300. Installed new radiator support rod cushions 90540-10022 and sleeve/tube 90440-11043 to properly square radiator. Measured and adjusted points dwell angle and adjusted carb using lean drop method. Then washed it to sadly put into hibernation due to road salt.
middlecalf
SILVER Star
@Ackcruisers did you find a reasonable functioning dwell-reading meter?
Ackcruisers
SILVER Star
I tried to justify buying a Fluke 78 but ended up with the Innova 3340. I’ll post in 40 tech thread the details.…
avicenna110
SILVER Star
Thanks for sharing! I also installed OME not too long ago which I think adds 2.5” lift. I’ve been trying to figure out why the steering felt a bit unstable at higher speeds (still manageable) and your post pointed me to the right stuff to research and read about. I’ll get the shims from Georg and add them when I swap the front axle to a later one with disc brakes (which I also obtained from @orangefj45 ).
GR starter in. Finished recovering my dash. I'm not sure this was the right way (I saw it on YouTube) but it's still nicer than the when it was cracked and crusty. Bondo'd the heck out of it and then recovered with marine vinyl.
Last edited:
Continued with my Vintage Air/Heat install today. It's coming along nicely.
suzuguru
SILVER Star
Man, that dash pad turned out really good. I'm impressed.
Check out this fancy pushrod cover! Getting swapped for the proper thing.
Gotta hand it to the PO the dang thing was glued on so we'll it didn't leak.
Gotta hand it to the PO the dang thing was glued on so we'll it didn't leak.
I guess if you can't track down the original and need to get moving down the highway, that will work. Was it leaking profusely?
