I have seen an ad on IG a few times for a product from Australia that attaches to the frame and uses your garden hose to flush the frame. Unfortunately I can not recall the name of the product, but it was well thought out and looked effective.
What Did You Do with Your 80 This Weekend? (48 Viewers)
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.
A binder clip also works perfectly.
Put the new RCV fronts to work on Yinsang (fka Chinaman) Gulch. Snow and ice made some optional lines impossible and the ‘easy’ line…very interesting. My steering wheel had been just slightly cocked after replacing the tierod’s TREs - slightly bent my Slee heavy duty relay rod backing off an ill advised line attempt on Whale’s Tale and now the steering wheel is perfectly centered 
.
We kept the 3rd gen Runner mostly to the easier lines. But not always - this is my youngest son’s rig and his older brother is driving here. But it did well on 35s and rear locker - this trail is very tight in spots and the 3rd gen body size can often wiggle through stuff I am going over.
This is coming down what I’m going up in the second vid below.
Some vid. In the first one you can see the how the normally grippy granite was slick even without snow - cold and wet tires don’t heat up even when you spin them a bit - if it doesn’t go where you pointed go where it went
.
.We kept the 3rd gen Runner mostly to the easier lines. But not always - this is my youngest son’s rig and his older brother is driving here. But it did well on 35s and rear locker - this trail is very tight in spots and the 3rd gen body size can often wiggle through stuff I am going over.
This is coming down what I’m going up in the second vid below.
Some vid. In the first one you can see the how the normally grippy granite was slick even without snow - cold and wet tires don’t heat up even when you spin them a bit - if it doesn’t go where you pointed go where it went
.
Last edited:
I read it as 50% "off" the parts...and I was going to ask...Where!!!!?????
Box Rocket
SILVER Star
I bought some new lights to put on my son's truck, but he blew up the motor and the truck is sitting at my brothers in Idaho. So I decided to try out the lights on the 80 until I can get my son's truck home to start work on the motor etc.
6.5" Trailblazer Driving Lights from LED-Colight. For an average size light they put out a lot of light and I dig the DRL. You can set up the DRL to be amber or white and can make it a turn signal also. I chose white DRL and no Turn Sig. Impressive little lights I think. Gonna be sweet on my kids truck. I'll be pulling these back off and moving them to my son's truck and keeping my 9" lasers on the cruiser.
Untitled by Adam Tolman, on Flickr
Untitled by Adam Tolman, on Flickr
Untitled by Adam Tolman, on Flickr
This pic is just my Projector Retrofit headlights
6.5”Trailblazer by Adam Tolman, on Flickr
This is about 10 seconds later with the Trailblazer lights
6.5”Trailblazer by Adam Tolman, on Flickr
I have purchased a bunch of different lights from these guys and they continue to impress me so I keep going back to them. My roof lights are also from them and the 9" laser spotlights I usually run on my bumper are from them. Because I have purchased a bunch from this company they sent me a message at the time I bought these Trailblazer lights and gave me a small discount and said I could share a link to get these light (and others) with a 15% discount. The link is on my Instagram @boxrocket_adventures if anyone is interested. Discount code for the Trailblazers is AdamTolman15. Code for anything else on there site is just AdamTolman.
I also tackled a bit of work on my rear bumper. Being 20 years old (DIY project) it has taken a beating. It was getting pretty rusty so I pulled it off to clean it up. I sanded it to bare metal and welded in some step pockets in the wings. Sprayed it with Raptor Liner and added some small LED turn signals since my 37" spare kinda blocks the passenger side taillight. Now I need to do the same with my swingouts.
Untitled by Adam Tolman, on Flickr
Untitled by Adam Tolman, on Flickr
6.5" Trailblazer Driving Lights from LED-Colight. For an average size light they put out a lot of light and I dig the DRL. You can set up the DRL to be amber or white and can make it a turn signal also. I chose white DRL and no Turn Sig. Impressive little lights I think. Gonna be sweet on my kids truck. I'll be pulling these back off and moving them to my son's truck and keeping my 9" lasers on the cruiser.
Untitled by Adam Tolman, on FlickrUntitled by Adam Tolman, on FlickrUntitled by Adam Tolman, on FlickrThis pic is just my Projector Retrofit headlights
6.5”Trailblazer by Adam Tolman, on FlickrThis is about 10 seconds later with the Trailblazer lights
6.5”Trailblazer by Adam Tolman, on FlickrI have purchased a bunch of different lights from these guys and they continue to impress me so I keep going back to them. My roof lights are also from them and the 9" laser spotlights I usually run on my bumper are from them. Because I have purchased a bunch from this company they sent me a message at the time I bought these Trailblazer lights and gave me a small discount and said I could share a link to get these light (and others) with a 15% discount. The link is on my Instagram @boxrocket_adventures if anyone is interested. Discount code for the Trailblazers is AdamTolman15. Code for anything else on there site is just AdamTolman.
I also tackled a bit of work on my rear bumper. Being 20 years old (DIY project) it has taken a beating. It was getting pretty rusty so I pulled it off to clean it up. I sanded it to bare metal and welded in some step pockets in the wings. Sprayed it with Raptor Liner and added some small LED turn signals since my 37" spare kinda blocks the passenger side taillight. Now I need to do the same with my swingouts.
Untitled by Adam Tolman, on FlickrUntitled by Adam Tolman, on Flickr
Took the pup out for a cruise.
Redid the stereo and added an under seat sub
Waiting for a few hundred parts to come from UAE for a full engine overhaul. Ron Davis rad going in, full ac refresh, York 210. Doing a 1 month trip next summer and going for it.
Waiting for a few hundred parts to come from UAE for a full engine overhaul. Ron Davis rad going in, full ac refresh, York 210. Doing a 1 month trip next summer and going for it.
- Joined
- Jun 21, 2011
- Threads
- 233
- Messages
- 21,831
- Location
- Redding, California
- Website
- trail-tailor.com
HA!
A few know. I bought the rights to the Cruisin Offroad rear bumper and skidplate products. So this is the rear pictured.
Jason
TT
NorCalFJ100
SILVER Star
I love my Cruisin Off Road skid plate. I think I was probably one of the last few to purchase from him.
Any black Friday coupons?
Installed OME 2861/2862 springs. Replacing the completely shot shocks with OEM Tokico shocks this weekend.
You back in action Jason?!
Egr homemade delete. And off to the Beartooth mts.
- Joined
- Jun 21, 2011
- Threads
- 233
- Messages
- 21,831
- Location
- Redding, California
- Website
- trail-tailor.com
P,
I'm doing a little more each day. The light stroke put me down more mentally than physically.
I can weld for about 3-4 hours now without the "SHAKES" kicking in on me. Today's work..
Hope Jan 1st I'll be back at a normal pace again.
Jason
TT
Last edited:
Your site is down?
- Joined
- Jun 21, 2011
- Threads
- 233
- Messages
- 21,831
- Location
- Redding, California
- Website
- trail-tailor.com
Glad to hear it! Work looks incredible as usual.
