Outsane
Supporting Vendor
Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature may not be available in some browsers.
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.
A couple pages back I posted that I was at emissions getting my 80 tested. Well she failed, but on the bright side the state of AZ has a program you can apply for. The state will help with $900 worth of repairs, I have to pay a $100 co-pay and anything over $1000.
I did check for vacuum leaks, with no luck. Checked the distributor for oil seepage but nothing.
Today I am picking up a OEM Toyota cap rotor today and will install them. The wires and plug wires have less then 10K miles on them.
After talking to the shop I am hoping it is just the catalytic convertors.
Not much 80 suspension left on that 80
Can you post up what the emissions were from the printout? Some of us can help point you in the right direction...
View attachment 3132024
@ToyotaDon hopefully this is what you were referring to.
Also, I seen you are from Visalia. My parents live of Akers.
Yes, that is what I was referring to. You are not going to fix that issue with catalytic converters, at least not permanently. What those number show is an extremely rich condition, or possible even a "dead" cylinder (think compression). I hate to be the bearer of bad news, but you need to start checking the basics of compression and whether there is something like a leaking injector. Does it even run smoothly?
What a small world with your parents living just across town from me.
You the man!Knuckles & axle are fresh & happy now. Weren’t bad, but truck has a slight extra crispness since. Never had to work on them. Agreed on easy job, just lots to do. Redundant at this point but @cruiseroutfit kit w/ koyos is and @NLXTACY witsend driver is sweet. Almost no sign of wear after 26 years. Switched birfs anyway. Found a bad trunnion bearing (fell apart upon removal), and PS abs tube broke off from the upper, but was able to fix well enough. Minimal swearing was limited to the fact that I hate hand pumping gear oil.
I still really like the idea of a birf goblet to go along with the oil filter tumbler, which I just ordered from @HemiAlex
View attachment 3131310
Take your time! It’ll be spending plenty of time on my boat & island camping next season.You the man!
I’m bound up with work but I can send it by Thursday. Thanks for the order!
Yup,, good call. I only happened to notice mine were about to burst when I was adjusting my wheel bearings. I wasn't even inspecting them, just glanced and saw it. Also went with the SS lines, they were even cheaper than OEM. lolInstalled my extended stainless steel brake lines. I also made sure to do the lines at the calipers since I was already there. A bit of a no-brainer if you're using 'old rubber' as an excuse to change out the other ones. This one just seemed like it took longer than previous installs. Now, I just need a helper to finish bleeding them.
Ran Slick Rock with several other Cruisers. We ran from Utica to Alpine. My first time running the trail in this direction as I usually start from Alpine. It's a whole new trail when you run the opposite way! Great trip and several rigs took home some new scars. Here's two videos
Would love more info on this, this is awesome!Plopped some things into a overhead console shell. Tmv71a faceplate, cheap switch panel, and cheap garage door switch wired to an opener. Works well.
View attachment 3130819
Thank you.Would love more info on this, this is awesome!
Nice! I love Slick Rock. You sure made that look easy. lol. I always have to do like a 10 point turn on that sharp left hander in your vide when coming down. Never gone from Utica up to Alpine either, always did the "downhill" route. Would love to join next time you guys roll up there!
Was this a recent purchase? Hard to tell but does it fully cover the opening on the headliner or still too small on the mount? Looks to still be the small, too small mount bracket and still no change.... I think it has been 2 years now they told me they were working on revising the mount.Installed Rosen visors on the Red
Was this a recent purchase? Hard to tell but does it fully cover the opening on the headliner or still too small on the mount? Looks to still be the small, too small mount bracket and still no change.... I think it has been 2 years now they told me they were working on revising the mount.