Builds Moonshine - A Build Thread (7 Viewers)

[woytovich]

Looks like time to clean your air filter maybe?

(probably been talked about before but... I could be wrong but I'm PRETTY sure that's not a 1FZ-FE...)

 

[cruisermatt]

I think your welds look great. Don't take negativity from Matt!

Good work Johnny

I don't have Alex's positive vibes

 

[GLTHFJ60]

Looks like time to clean your air filter maybe?

(probably been talked about before but... I could be wrong but I'm PRETTY sure that's not a 1FZ-FE...)

Good call on the air filter. It's a RCV cleanable paper air filter. Believe it or not that's right after a clean.

Next thing moonshine will get in the engine bay is a proper Donaldson air filter. Hopefully this little guy lasts till then. If not, I have another larger filter in the garage.

 

[GLTHFJ60]

Dude, I TOLD you I thought it had a softer pedal then it should!

I knew it had a soft pedal, just didn't know that I had the brake lines hooked up backwards, lol.

 

[cruisermatt]

Well now you have me thinking about mine...

 

[GLTHFJ60]

I've been distracted of late, expanding my garage, but I did pick up a fun part today

 

[GLTHFJ60]

Finished the garage project. Here's a photo close to the end:

Got prepped for the axle rebuild:

Got the stuff together:

Pulled the axle out:

Put it on the rack I built that attaches to the welding table:

Started the shave:

Welded up the drain plug you saw two pics above and the screw hole since the housing was preheated anyway:

Ground smooth:

Painted:

Cleaned and painted a bunch of stuff, installed the ring gear on the ARB carrier:

Mmmmm, preview:

 

[Cruiserdrew]

Wow, that is super sexy. And it represents a lot of hard labor. Nice going. 14B for the win! As always.

Rubithon? The new wife said you could go.

 

[GLTHFJ60]

Wow, that is super sexy. And it represents a lot of hard labor. Nice going. 14B for the win! As always.

Rubithon? The new wife said you could go.

Thank you sir!!! We'll chat about rubithon

 

[White Stripe]

Nice garage man, looks well setup.

 

[Wrench]

Did you shave it?

 

[hman913]

He's using a Barnes 4WD 13 bolt cover so you can cut off just over 1" from the bottom of the housing. Doesn't yield as much clearance as a true shave, but this way also avoids having to weld to the center section.

 

[boots4]

Very nice and awesome having an indoor work area. I had a house building friend tell me you can never have enough bench space in a shop and he was right, all my bench space has stuff on it too. Jealous of the rear locker, hopefully that's on my not too far away list. Sadly one of my boys broken his arm this month so funding will be tight for a while.

 

[KWalkerM]

I saw Moonshine on Instagram the other day. Neat-o, that is all.

 

[Tapage]

Johnny did you move it ( 14B ) alone ..? you must be superman .. !

 

[Wrench]

How much does it weigh?

 

[cruisedeisel]

I am embarrassed to say, this is my first time checking out your long quest of your moonshine madness. Sweet stuff!!!

 

[Cruiserdrew]

How much does it weigh?

I have two 14 bolts at home and they are about 450-500 pounds each. Twice the weight of a Toyota axle. If they still have the original drum brakes, add 100 pounds. Seriously this is some solid American engineering. Note the front pinion support. I wish Toyota had adopted that. It's like a Ford 9 inch, only much better.

 

[S4Cruiser]

Finished yet ?

 

[GLTHFJ60]

Nice garage man, looks well setup.

Thanks!

Did you shave it?

He's using a Barnes 4WD 13 bolt cover so you can cut off just over 1" from the bottom of the housing. Doesn't yield as much clearance as a true shave, but this way also avoids having to weld to the center section.

Yes I did shave, not 100% accurate though. Since this is technically a "AAM 10.5", not the old Corporate 14 Bolt, it has a drain plug in the bottom center of the housing, right where you do the 13 bolt shave, so you do have to weld up the hole. Not a big deal.

Very nice and awesome having an indoor work area. I had a house building friend tell me you can never have enough bench space in a shop and he was right, all my bench space has stuff on it too. Jealous of the rear locker, hopefully that's on my not too far away list. Sadly one of my boys broken his arm this month so funding will be tight for a while.

Thanks Mike I actually eliminated a workbench in my shop. I have a condition called FSD (flat surface disease) so I have to limit how many workbenches I have.

Sorry to hear about your boy's broken arm, but they bounce back quickly. Definitely check out the 1/4" air line mod I did (next post), I think you'll want to do the same on your truck.

I saw Moonshine on Instagram the other day. Neat-o, that is all.

That was @mcguirejohnson . I met up with him and his pops @CenTXFJ60 at a BBQ joint in NC before XMas. Awesome guys and they bought my dinner!!

I am embarrassed to say, this is my first time checking out your long quest of your moonshine madness. Sweet stuff!!!

Thanks! There's a lot of info here. I was quite the n00b when I started this thread.

Finished yet ?

Getting there Still loving that vice man!!