What have you done to your Land Cruiser this week? (41 Viewers)

[Stumpalama]

That hanger looks mangled as well. Perhaps that contributed to the failure?

and yeah, I mangled yet another spring pin

don't know whether it was this weekend, but we discovered it Saturday as we were trying to flex the truck with the new tires on some rocks

sorry, Kurt, that was one of yours (I'll send it to you when it's out) - have a spare on the shelf already

otherwise, I had fun

 

[JohnnyC]

this week I pluged in the block warmer for one day ... i didnt want to walk or bike into work at 3deg's

 

[MyTwoToys]

Picked up some parts from the paint shop #653 Olive Green, or Brown depending on who you listen to. Installed the header and my new SOR oil lines. Hope to get the body on in a few weeks when it is back from the paint shop. Plus working on completing the rebuild of my 8274 Winch and hoping it gets above zero in the next few days so working in the garage isn't so painful.

 

[Waterboy]

Packed her up. Heading to Trollhole.

Sent from the islands.

 

[Vae Victus]

Packed her up. Heading to Trollhole. Sent from the islands.

Cool. For?

 

[OverLand Cruisers]

Hmm...a trip to Trollhole, cool!!

I started wire wheeling the tub of the '78 in preparation for Rust Bullet & new paint. Not much rust as it is a CO/AZ rig, however I want to get it 100% rust free & perfect. The OE rubber mat & insulation + trapped moisture=bad.

 

[Waterboy]

Cool. For?

He's gonna get running and driving.

Sent from the islands.

 

[aggiecruiser]

Packed her up. Heading to Trollhole. Sent from the islands.

Waterboy, what is the opening clearance on that enclosed trailer you are using? Is that a custom trailer?

Sent from my iPhone using IH8MUD

 

[Waterboy]

Waterboy, what is the opening clearance on that enclosed trailer you are using? Is that a custom trailer? Sent from my iPhone using IH8MUD

Not sure if it's custom or not. I believe he said its a seven foot clearance. I'll ask the carrier next time I talk to him.

Sent from the islands.

 

[DSRTRDR]

That hanger looks mangled as well. Perhaps that contributed to the failure?

I suspect so - will need to be addressed

 

[DSRTRDR]

Packed her up. Heading to Trollhole.

that's an expensive way to get a wiper and a bumper

 

[Stumpalama]

I should be able to run just about every Toyota truck drive shaft bolt pattern now.

 

[Texaszed4mc]

Got the heater working, Finally the blower motor now works, but just one speed. It sure is nice to have heat in the Red Monster!

 

[nelsonjm624]

Worked on my console a little bit, still have to do the front plate, a lot of weld grinding, make the lid, add a two cup holder on the back.

 

[user42]

Cut off the rocker, most of it anyhow

Posted via IH8MUD app

 

[Mongoose317]

Got my power steering pump cleaned up for the 3fe swap I'm working on for my 40. Bad news was I found that the pulley on the shaft had been loose. Shaft appears ok but pulley shot! Just ordered a new one and a seal kit. Yikes, you would think the pulley was gold plated.

 

[ibinazbass]

Took her up to the shop I work at to do the fabrication stuff I can't do in my apartment complex garage.

 

[youmustbecrazy]

Been a while since I have posted on this thread. Threw the hardtop on and actually fully bolted it on, put on the Con Ferr rack for the first time on this cruiser. Also new since last time I posted are the H1 rims with 37" military take offs.

 

[PWCO70crusier]

Got the seats torn apart and painted. They should be off to the upholstery shop in the next week or so. Next up is ordering wire harness materials...and the fun begins...
http://kyle-landcruiser.blogspot.com/

 

[PWCO70crusier]

Got the seats torn apart and painted. They should be off to the upholstery shop in the next week or so. Next up is ordering wire harness materials...and the fun begins...
http://kyle-landcruiser.blogspot.com/