What have you done to your Land Cruiser this week? (33 Viewers)

[tls3601]

Will be 38 years in April to the best wife in the world. Did ya see the transmission on the dining table?

View attachment 3243036

Awesome, way to go dude

 

[suzuguru]

Still plugging away on the valley area between the door and the passenger seat mound. Have some touch ups to do but it’s looking factory again.

Have to plug a new tool that’s changing my life. Anyone doing body work on a 40 should get the new Milwaukee bandfile. No affiliation, just trying to help ya’ll out with those difficult to reach areas.

View attachment 3259601
View attachment 3259597View attachment 3259598View attachment 3259599View attachment 3259600
lots of hours getting that contour correct. Had to utilize three separate pieces because I don’t have the skill to do it all in one sheet!

Man, that is so crazy! I was just telling a friend the other day that they needed to invent one of those! I could have used one so many times! Awesome!

 

[TRAIL TAILOR]

I keep taking these correction builds... I just feel sorry for these customers and feel I need to help... Customer brought this recent build in from another local Redding, CA shop *(shop moved out of state now)* for corrections.

Suspension & shock issues ( 2" higher in front than rear and only 3" of shock travel in the rear on flex- procomp front and rancho rears) Will be replacing with Dobinson IMS shocks , brake lines were hard mounted and rubbing through at frame and knuckles, starting ( ignition ) issues, rear shock rubbing exhaust, transmission/motor shifted wrong direction on motor/5 speed swap and drive lines are 5-7 degrees off. Front axle needs a minimum of 4-6 degrees to correct caster and toe in was set at over 1/2" with 33" tires on initial inspection.

@orangefj45 ... I'm gonna need some parts on this one.........

Jason
TT

 

[Chungas Revenge]

With my wife’s help to pump the pedal, I finished the first full overhaul of the rear brakes on my LWB in the 29 years that I’ve owned it. Always dodged the full overhaul before by honing the cylinders on the truck.

Made some new brake lines while I was at it. And for that, I give thanks to MUD. I learned about both the Nicopp tubing and the flaring tool from this forum.

View attachment 3252799

29 yrs on “preventative maintenance“…well done.

 

[Roastchestnuts]

Got a couple of photos of my fj40 on expired portra 160 vc 220 film with my fujigw690III. Film was certainly stored well!

Very small waves but ended up being fun!

 

[65swb45]

29 yrs on “preventative maintenance“…well done.

Funny, scary story. When I bought the truck in ‘94, it was only 30 miles away, and I insisted on having it towed to the shop even though it drove.
I had a customer at the time who wanted to help out at the shop and earn credit towards parts, so I had her take the tires and brake drums off the truck so I could inspect them.

When I started pulling out wheel cylinder pistons, puffs of dust came out with each one.

 

[mattressking]

Bored with a few carbs laying around and my suspicion is right, a late 69-74 carb lid fits and lines up with all ports on a 75-87 carb body. Which means to me, you can make a hybrid to fit the early air cleaner to a late ROW carb and still use your early choke.

Forgive me if this is known, but I’ve never seen anyone try it or apply it. It’s not important or applicable for most but neat to know for myself, hopefully someone can make sense of it. This way you don’t have to hack up an air cleaner or bracket to fit it all.

Don’t mind the picture, I had it resting for the pic, should’ve bolted it down to make it clear. Gaskets and bolt holes all align as they should.

 

[middlecalf]

But that still looks like a 3 job from your pic @mattressking .

 

[dkcrew]

Passed inspection this week!!!!! And ordered a new gas tank to eliminate the flow of rust. looking forward to receiving and installing that soon.

 

[Almill13]

Perfect evening for a cruise to the taco truck

 

[Michael B]

Perfect evening for a cruise to the taco truck

View attachment 3261027

Nice wheels! What size are your tires?

 

[dragonbyu]

Perfect evening for a cruise to the taco truck

View attachment 3261027

I forgot about Mamacita’s. We normally hit up the Taco truck that parks next to Macs Customs on New Hope.

 

[thatcabledude]

Perfect evening for a cruise to the taco truck

View attachment 3261027

What wheels are those?

 

[Michael B]

What wheels are those?

They appear to be modified GM ralley wheels.

 

[Almill13]

Nice wheels! What size are your tires?

31x10.5 R15

 

[Almill13]

I forgot about Mamacita’s. We normally hit up the Taco truck that parks next to Macs Customs on New Hope.

We love Mamacita's we go almost every Tuesday. Good to know there is a fellow cruiser guy near by. Maybe we can meet up for tacos and toyotas one night.

 

[Almill13]

What wheels are those?

They were on the truck when I bought it so I'm not 100% sure but they look a lot like Chevy C10 rally wheels.

 

[thatcabledude]

They were on the truck when I bought it so I'm not 100% sure but they look a lot like Chevy C10 rally wheels.

Thanks. I’m gonna have to investigate these. I’m sure I could probably figure a way to attach 40 hubcaps.

(Maybe that’s been done before already?)

 

[Green Bean]

Installed an intake manifold vacuum with an added port to aid in taking vacuum readings more expediently without removing the 4WD hose.

 

[EWheeler]

Installed an intake manifold vacuum with an added port to aid in taking vacuum readings more expediently without removing the 4WD hose.

View attachment 3261389

View attachment 3261390

View attachment 3261391

View attachment 3261392

Nice! Where did you source that part?