It's wierdly not leaking. I have an engine refresh coming soon though, so all the gaskets will get replaced then. Trying to figure out how to keep the valve cover cork to seat right and keep from leaking.
What have you done to your Land Cruiser this week? (60 Viewers)
- Thread starter IH8MUD
- Start date
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.
It's wierdly not leaking. I have an engine refresh coming soon though, so all the gaskets will get replaced then. Trying to figure out how to keep the valve cover cork to seat right and keep from leaking.
Finally got the rear doors done.
orangefj45
Supporting Vendor
3M black weatherstrip adhesive. And run a rubber gasket not cork.It's wierdly not leaking. I have an engine refresh coming soon though, so all the gaskets will get replaced then. Trying to figure out how to keep the valve cover cork to seat right and keep from leaking.
Got lucky and found a wiper assembly. Installed it. Gotta get a switch and wire it up now.
Well my little one is 16 months now and will have another here in September so about time for a child seat in the 40. I've had this jeep seat stashed away for about 6 years. I wanted something non invasive so came up with this without having to drill any new holes. Still need to make some seat belt / child seat anchors.
Last edited:
New wheels and new tires. Installed a pair of used OEM headrests.
Everyone is thinking it...didn’t they sell any TRUCK tires there?
I refurbished the original seats
Catching Neutral
GOLD Star
Drove it to a sunrise session of beach volleyball with the guys which was unfortunately interrupted by work.
Tore apart my failed throttle position sensor and took a picture of the inside. Apparently one end of the potentiometer connection opened up.
- Joined
- Apr 14, 2004
- Threads
- 1,472
- Messages
- 36,750
- Location
- 818-953-9230
- Website
- www.marksoffroad.net
Pulled the sort-of-fit round Toyota coolant bottle and bracket out of the 45lwb and replaced it with one of @ToyotaMatt sano core support mounted units. Had to drill the strut and core support out to 8mm, but otherwise plug n play.
I was going to scuff the paint on the right fender to prep it for paint. Looks like a battery leaked a loooong time ago, so I'm going to take it down to bare metal.
Any plans for 3 point belts once the little is in a bigger seat? Ive been trying to get something planned for my 2 ladies 5 and 2.
No not yet. Maybe down the road.
Was it tough to mate up the floor part that I didnt cut very clean?
It’s not completely welded yet, as I’m still fitting the doors but not to bad.
for sale?
my fellow Greek friend , your new , refreshing approach to the early Rotory knobs topic
Is personally VERY inspirational and motivating
For me ...
I simply love your concept visionary approach to your interpretation. Of what could
Have been and what indeed was ...
again good show !
i saw this post right after you hit it ...
So , I hit The “Skunk-Works Lab “. Beneath my shop and became engrossed in a all night marathon
To. Make some needed head way on my various
Special custom Taylored knob and switch restore
Orders I have going on ....
here for your review , my Greek Phrend ..
note: the JDM Canary Yellow Lantern lumen rays
Bursting is my SEMA type theme Kustom prototype
And might just be my vision and my answer
To the current extremely outdated and dreary dismal analog FOG switch knob commonly
Available that everyone is familiar with
that old outdated fog text font logo was intruduced
All the way back in 1972 , perhaps earlier maybe ?
it’s time for a 1985-Later 40 series update of what could and should have been in my opinion , in my personal . TEq world ......
View attachment 2305803View attachment 2305804View attachment 2305805View attachment 2305806View attachment 2305807
I got a bit of my emissions system reinstalled.
whoops ,
one got out early .........
there part of a bigger picture , plug and play illuminated back lit knob
FOG switch set up's ..& AUX switch ones too 2nd one below , then
OEM HAZARD
prototype development is done and results are more then i could ever of hoped for
there is the one you cleverly screen-shot 1st pic below it too ..........
you may recognize the OEM Text font logos below it too .....
Last edited:
