- Thread starter
- #201
Pic of compressor leaking
Builds 1994 BUILD OUT and LS swap! Let's Go! (1 Viewer)
- Thread starter TLC94LS
- Start date
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.
- Thread starter
- #202
here is some info on how I hooked up the alternator to get it to work at its highest charging potential and retain the function of the battery charge light.
- Thread starter
- #203
Finally getting back to some projects. Working on re covering the front seats with new leather from LS seat. Also my bumper is almost finally going to be shipped from Delta. Can not wait to get my rig on some trails this fall. Finally!
- Thread starter
- #204
This happened at school pick up today.
tmxmotorsports
SILVER Star
You show em what's up?
FMC80
SILVER Star
I like yours better
- Thread starter
- #207
Funny it was my buddy’s wife. They just got it. I was a bit envious of the creature comforts for sure. They are real nice inside. I wish I had paid attention to noise reduction and heat control on the firewall and trans tunnel. Next time I guess. Imi e still has factory stereo in it, it’s so bad I don’t even turn it on.
- Thread starter
- #208
Info on my fuel line drama.
- Thread starter
- #209
Got it sorted out. Good as new.
- Thread starter
- #210
Overall update on my project. I re did my fuse box because I gooned up by removing the pins multiple times. Wrapped and secured all the engine bay wiring. I put thermal protection on the trans cooler lines. I’m happy how it all turned out.
My @Delta VS rear bumper is supposedly being shipped any day. I can’t wait to get this vehicle outfitted and ready to go.
For the inside. I’m about to pull the carpet out and pressure wash and clean them. Had an incident with some elk meat getting left in there by mistake! Seats will be recovered and foam dressed up. So I’m finally hoping in few weeks to get it wrapped up and ready for fall.
Has anyone used any of the sound proofing products in your project?
My @Delta VS rear bumper is supposedly being shipped any day. I can’t wait to get this vehicle outfitted and ready to go.
For the inside. I’m about to pull the carpet out and pressure wash and clean them. Had an incident with some elk meat getting left in there by mistake! Seats will be recovered and foam dressed up. So I’m finally hoping in few weeks to get it wrapped up and ready for fall.
Has anyone used any of the sound proofing products in your project?
Last edited:
I did. I sprayed Lizard Skin sound deadening and Ceramic Insulation, then layed MAT66 ProBlack Car Sound Deadening Mat.
- Thread starter
- #212
I put down a box of sound proofing and foam on top. Really looking forward to getting my seats finished.
- Thread starter
- #213
When I purchased the LC, it came with a standard ARB bumper. I want to add a winch as I think it’s a must if you’re going offroad and expect to be at work on Monday! Is it possible to cut out an opening for the line and four bolt holes? Is there additional internal bracing on an ARB winch ready bumper?
- Thread starter
- #214
Can anyone give some tips on what the proper technique to go from H (high) to L (low) gearing with the pin 7 mod done on the center diff. Thanks. Not sure of the center diff should be unlocked while transition from H-N-L or not. Thanks
NeverFinis
SILVER Star
I don't think it matters mechanically. Unlocked or Not.
I did it to mine. Others have done it too. Turned out very nice.
- Thread starter
- #218
Oh awesome, you’re going to have to send some pics. I’ll let you know when I get there.
dirtyboots
Atrocious Driving
Google sound deadener showdown, the website is shut down but numerous other threads and sites reference the info from that now closed site..in short don’t cover the entire interior with an adhesive mat. Additionally coveinrg the entire interior surface can affect denting of exterior sheet metal like on the roof. Use a combination of products strategically like rolls Royce. I used MLV, CLD tiles, and a foam I can’t remember on the floor, 3m something fill in between the headliner and roof and lizard skin sprayed in the tunnel. Could I be more vague? HTH just hate to see the slather everything with adhesive mat whe it doesn’t work as well and costs as much or more than a proven result. Nice build good luck!
- Thread starter
- #220
Well thanks for the input on the sound proofing. Guess it’s too late now. I put closed cell foam over the rubber mats. I wish I had thought about this when I had the engine out I would’ve sprayed the firewall and engine trans tunnel. I really don’t feel like dropping the headliner at this point.
