mattressking
10 digits to freedom
original motor but fresh carb and dizzy - I advance timing to 10* so I run 91 to prevent any potential pinging.
What have you done to your Land Cruiser this week? (24 Viewers)
- Thread starter IH8MUD
- Start date
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.
Threw together a bracket from angle iron for the generic radiator overflow bottle.
Last edited:
PTO winch, finally complete!
The
was great, managing the clutch to wind the original wire rope back onto the drum.
This is the original factory arrangement of 165 ft of 5/16" rope plus the 3/8" chain and slip hook.
The
was great, managing the clutch to wind the original wire rope back onto the drum.This is the original factory arrangement of 165 ft of 5/16" rope plus the 3/8" chain and slip hook.
i like your #7 Bolts Mr Letterman
Keen eye. They are from a sponsor who doesn’t know he’s sponsoring me.
Used some of the sheet steel left over and made a cover for where the stock heater blower use to be. Mounted the Robb MC power surge there instead. Just need to clean up the cover and paint it.
Last edited:
Finished my tire carrier build
Mtntopper
SILVER Star
Tire rotation time. The play in the steering linkage cups the front tires pretty quickly.
KingAir Driver
SILVER Star
Installed a new brake booster, brake master cylinder and front main soft line from @Racer65. Quality products like usual. Made sure everything was adjusted and bled. Think my overheating drums are cured, temps from 190F down to 120F now. Plus, power off idle is so much more responsive, without a bad booster.
You mean this leaky booster is costing me power? Well that changes everything!
KingAir Driver
SILVER Star
I know Matt, it’s on my list at some point.
Skreddy
SILVER Star
I have the same original bracket on my 71, but no bottle or washer nozzles. Was the bracket included on all 40’s?
i was first a PIO or PORT INSTALLED OPTION , then standard equipment in 1972ish
I think You should Explore this LINK :
OEM TECH and FACTORY JAPAN NOS Bottle with PUMP s at the other end ...........
12v VOLT GENUINE NipponDenso JAPAN 12 Volts NON USA OEM TOYOTA Windshield Washer Bottle Resiover KIT 85330 , MOTOR PUMP , , 200mm BLUE-TINT JDM Style Washer Hose 1/62 - 10/84 Fj40 FJ50 FJ55 BJ40 , BJ42 , BJ43 , BJ44 , BJ45 , BJ46 , HJ45 - VintageT
GENUINE NipponDenso JAPAN 12v / 12 VOLTS Note : Kit Comes with Smaller Black Bracket , ONLY .......
vintageteqparts.com
Skreddy
SILVER Star
I debated that very setup while doing my restoration, but since I had no squirters or wiring, I opted to not add the washer kit. But I kept the bracket for the next owner if they want to go down that road. I’ve seen generic squirters in the hood on some 40’s, then some without. 3 of the other cruisers I’ve had didn’t even have the bracket; but I guess they were missing a lot of stuff, besides rust and a lot of PO holes.
More like what have I done FOR my Land cruiser this week.
Im building a gazebo structure to park my 40 under. It’s a kit that comes in a million parts. The ultimate “some assembly required“. It’ll be nice to have it under a solid roof and behind a gate. So now all the sub assemblies are done and I just have to put it up. Stay tuned.
Im building a gazebo structure to park my 40 under. It’s a kit that comes in a million parts. The ultimate “some assembly required“. It’ll be nice to have it under a solid roof and behind a gate. So now all the sub assemblies are done and I just have to put it up. Stay tuned.
these kits come with 2 nozzle jets assy's
each have one has only one squitter hole , NOT 2 like late modle fl40's
there small and round capsule shaped , fro my R&D , and i DUG hard this is same exact period correct parts kits from DENSO Japan today i source and back in the DAY one
post PLANT A-11 Fist Test DRIVE bfore being loaded on the Freighter on way to LONG BEACH PORT of entry in CA........
so check my PERSONAL Collection out here
this is all Stuff i have collected since high skool in 1990-1992 ...
from Carlise Car swap meats in Pennsylvania
like this i Caught a while back .........
