Maybe the slow jet is clogged ?It had been running fine, I didn’t move the distributor that much.
What have you done to your Land Cruiser this week? (76 Viewers)
- Thread starter IH8MUD
- Start date
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.
To : Mark Hawley @ Metal Tech
After 23 years my 40 finally has it's set of NLA Metal Tech 40 tube fenders. I retained the oem inner fender brace and welded tube to it. I did not delete the apron so I just used the original fender and cut it back.
After 23 years my 40 finally has it's set of NLA Metal Tech 40 tube fenders. I retained the oem inner fender brace and welded tube to it. I did not delete the apron so I just used the original fender and cut it back.
- Joined
- Apr 14, 2004
- Threads
- 1,477
- Messages
- 37,073
- Location
- 818-953-9230
- Website
- www.marksoffroad.net
I remember talking about this and you showing me the tubes when I stayed at your house! Wasn’t that like 18 years ago? You told me then that you were going to try and retain the aprons and I told you then that I liked that idea.
I still do.
I'm more concerned about the condition of your vacuum and mechanical advance in the distributor and where you're getting your vacuum signal from. To your knowledge, is this the original distributor? Are you full manifold or ported vacuum?It had been running fine, I didn’t move the distributor that much.
That looks really good.
65swb45, thank you, I thought it was 02' 03', could have been later, either way, past due for sure.
This vision has been in my head for that long, sense of closure now, feels satisfying. Mark A., it is unique to share a thought/concept with someone and having them around at it's finality, I like the " Remember when we talked about this years ago " comment, I guess it makes me feel like I actually completed a task/ wishlist item regardless of how large a task it was. I appreciate being able to share that with you.
This vision has been in my head for that long, sense of closure now, feels satisfying. Mark A., it is unique to share a thought/concept with someone and having them around at it's finality, I like the " Remember when we talked about this years ago " comment, I guess it makes me feel like I actually completed a task/ wishlist item regardless of how large a task it was. I appreciate being able to share that with you.
- Joined
- Apr 14, 2004
- Threads
- 1,477
- Messages
- 37,073
- Location
- 818-953-9230
- Website
- www.marksoffroad.net
Want a laugh? I also remember being so impressed with your idea that I asked you to consider building me a pair!
I’m not waiting another 18 years!
Well now I know exactly how to do it, do it better the second time & make them bolt on if nec., it was kinda fun. I also got to delete those lites, the new ones are metal bodied ( not plastic) LED , have park & blink, and because I have filament rear bulbs the flasher still works and they cover the holes.
The fitment of the cut back skin is tough because the fender isnt square, bent over the years, etc. & after looking at my hood overhang and reading your post I checked, sure enough driver side front cab mount area is bent due to repeated smashes at rear of rocker which is tied to frame & tub right there. No way could you make them without vehicle in hand.
The fitment of the cut back skin is tough because the fender isnt square, bent over the years, etc. & after looking at my hood overhang and reading your post I checked, sure enough driver side front cab mount area is bent due to repeated smashes at rear of rocker which is tied to frame & tub right there. No way could you make them without vehicle in hand.
That's what I do in the People's Republic of NJ. Historic tags. It's a great loophole.I need to get those collector plates too @Skreddy . Technically every drive in the 40 can be considered “for testing purposes” since you never fully know if something is going to break.
They get set in their ways sometimes. LOL. I've been there with mine.I’m not sure what I did, but it’s running better now. Probably have the idle a tad high, but I tried driving it hard-ish, bogging it, decelerating, fast stopping, etc and it didn’t die on me, so…I’ll just accept it for now.
View attachment 4001450
I removed my drivers seat bracket and modified them bc I needed more leg room. I could only move it back 2" bf the back of the seat hit the rear fender well. What a difference. I works great with the factory brackets. Just drill the rivets out and move them 2" and reweld them.
MatthewMcD
SILVER Star
This timing light is the bomb for timing, RPM, and dwell (if you still run points). https://amzn.to/4nQuEtS It may seem expensive, until it saves you hours on your truck.
101% correct…..
- Joined
- Apr 14, 2004
- Threads
- 1,477
- Messages
- 37,073
- Location
- 818-953-9230
- Website
- www.marksoffroad.net
I concur. And I'd like to add that is one of a few tools that I have that I didn't know about until I read about it on this forum.
MatthewMcD
SILVER Star
I like the advance feature that allows you to dial in the advance and see the BB in the window. Excellent for checking vacuum advance.I concur. And I'd like to add that is one of a few tools that I have that I didn't know about until I read about it on this forum.
- Joined
- Apr 14, 2004
- Threads
- 1,477
- Messages
- 37,073
- Location
- 818-953-9230
- Website
- www.marksoffroad.net
I've had an adjustable advance light since before I opened the shop, but it died. I like the fact that I can measure timing AND dwell without having two sets of wires to keep track of.
MatthewMcD
SILVER Star
These arrived today. To be honest, I am more worried about this upgrade than I was about the engine swap.
12 of the scariest rusted bolts on the truck. I have loosened 4 of them and started soaking the rest.
If anyone has any tips let me know.
12 of the scariest rusted bolts on the truck. I have loosened 4 of them and started soaking the rest.
If anyone has any tips let me know.
Thank you for sharing this
If you are sure carb has been cleaned thoroughly and the idle port is clear, I would focus on the finding potential vac leaks, I struggled with this whole thing for what seemed like a few months and was finally able to solve my issues by finding the leaks, adjusting the sticky throttle linkage and replacing the idle jet with a slightly larger one. A simple vac gauge like this one is key for solving your tuning issues. I actually use it in the rig ! Good luck and DO NOT GIVE UP!One thing I have noticed is the idle mixture screw seems to have no effect (by ear anyway) on rpms.
According to the carb video above you back it out to raise the rpms, then turn the idle screw to bring them back down, and repeat.
I had it all the way in and several turns out with no change.
Last edited:
