What have you done to your Land Cruiser this week? (66 Viewers)

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

BRShap said:
How do you separate the dial and spring assembly? Just remove the snap ring?
Click to expand...

forum.ih8mud.com

Warn Hub (coarse spline) Cleaning and Rebuilding

One of my "take home" projects while my FJ40 is being worked on by Mark (marksoffroad.net) has been to cleanup and rebuild a pair of Warn M193 hubs for my coarse spline birfs. These will be replacing the failed Selectros. I bought a pair of dirty used hubs during one of my stops at the shop...
forum.ih8mud.com forum.ih8mud.com
forum.ih8mud.com

Warn hub rebuild/repack procedures

Hi there. About 6 months ago I purchased a 1978 FJ40. Am still in the process of replacing / rebuilding mechanical parts on it. I by now rebuild the master cylinder, clutch master and slave, radiator, fan complete rear breaks and some other minor parts and pieces to get the truck running...
forum.ih8mud.com forum.ih8mud.com
I had to move the snap ring up the dial a bit to get the spring assembly off the roll pin. Reassembling it was easy. I fully seated the dial, put the snap ring on, and the spring assembly threaded right on. Not sure what the difference was. I did one at a time to make sure I was putting the roll pin back into the correct hole on the spring assembly.
 
I got my wiper motor mounted and correctly working both the high and low speeds. Rebuilt the wiper harness with supplies from @Coolerman and his detailed instructions in his Wiper Science write up from the switch to the motor were outstanding.

I was able to top it off with a great new switch cover ....made by @ BIG RENO AL

Another MUD discovery was Hosa Contact Spray....worked great.

Amazon.com: Hosa D5S-6 CAIG DeoxIT 5% Spray Contact Cleaner, 5 oz.: Musical Instruments

Amazon.com: Hosa D5S-6 CAIG DeoxIT 5% Spray Contact Cleaner, 5 oz.: Musical Instruments
www.amazon.com
1915295
 
Whats a FJ40 tub trailer worth, if you don't mind me asking? I have a 68 (or 69) parts vehicle that I am thinking of making a trailer out of just for the fun of it, but don't know if all of the parts are worth as much as keeping it whole?
 
Birk said:
Whats a FJ40 tub trailer worth, if you don't mind me asking? I have a 68 (or 69) parts vehicle that I am thinking of making a trailer out of just for the fun of it, but don't know if all of the parts are worth as much as keeping it whole?
Click to expand...
I was lucky and got it for $1,100... but if you price it in parts alone your looking at about ~$2,500 not including labor.
 
Made up the brake hard lines. I've got the front done and now the rear is half done. I gotta shove 2ft of snow away from it if I want to be able to crawl under it and start working on the last of the rear. One 25ft roll is enough to do everything but the rear axle from the looks of it so I'll need to pick up another one. My little Master cyl spacer plate gives just enough clearance to get the bit 9/16" tube nut on without having to clearance the firewall rib.

Might finish that tomorrow if it doesn't snow again.
 
Last edited:
Going in knee deep...
Changing manifold and head gaskets this weekend.
Pic taken two days ago. Snow in Salem is a rare treat.
IMG_4433.webp
 
You must log in or register to reply here.

Similar threads

Mike Shull
Where Have you Driven Your 40-Series This Week?
14 15 16
Replies
306
Views
30K
bernardbar3
bernardbar3
T
What is this?
Replies
11
Views
604
jim land
jim land
C
  • Question Question
What tools do you keep in your FJ40?
2 3
Replies
42
Views
4K
65swb45
65swb45
wchevron
What size lift do I have.
Replies
10
Views
708
JackA
JackA

Users who are viewing this thread

Total: 67 (members: 8, guests: 59)

Share this page

Back
Top Bottom