Vae Victus
Posting more than I know
Drove it 50’
... in REVERSE (3 spd tranny hung up)!
... in REVERSE (3 spd tranny hung up)!
What have you done to your Land Cruiser this week? (29 Viewers)
- Thread starter IH8MUD
- Start date
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.
I haven't seen the video but Jerry Seinfeld interviews Ellen driving around and a 1977 FJ40, the link to video is at the bottom of the page:
Watch Spotting: Ellen DeGeneres Wearing A Paul Newman Daytona On Comedians In Cars Getting Coffee
Just fyi,
Zona
Watch Spotting: Ellen DeGeneres Wearing A Paul Newman Daytona On Comedians In Cars Getting Coffee
Just fyi,
Zona
oregon fj
Serial rescuer of old vehicles
Still torn to bits. But the bezel is right-side-up.
Last edited:
Looks like youll be back on the road in a few weeks....
On vacation and with all the ‘sights’ one expects to see at the beach..... here’s what really caught my attention!
*Damn, I’m gettin OLD!
*Damn, I’m gettin OLD!
Last edited:
After 4 years of living in my shop in a frame off restoration which included hours and hours of fixing minor nicks and dings and two coats of 2K primer along with hours of sanding, the body and all other sheetmetal parts went to the professional painter today for a base coat/clear coat finish. This guy has done work on Jay Leno's vehicles and is really good. The amazing thing is he lives about 5 miles from me. The shop shop so empty...Time to roll the rebuilt and assembled frame in from the other garage to prep for the body's return in a couple of weeks.
thebigredrocker
SILVER Star
@Helipilot Have you asked him what paint he’ll be using?
David70FJ40
Older Than Most
The local Toyota dealer parts man said the OEM PCV valves weren't available in the USA. Followed the link provided by a previous poster to SOR and they listed theirs as OEM so I took a chance. Arrived today, has the Aisan name on the side, heavier and better made than the Echlin I got at NAPA and with just a little pressure after lubricating it almost fell into place. The Echlin was a bear to force in and I wasn't real sure it was seated properly. The Aisan is tight and seated properly. There is a lot of reason why to stay with Toyota parts.
Sorry for the fuzzy photo, at least you will get the idea.
Sorry for the fuzzy photo, at least you will get the idea.
marketShark
Spider 2 Y Banana
Just saw this- looks like ARB is rereleasing the "catchers mask" for limited run. Will be about $920 USD (converted from AUD in their post).
EDIT FOR LINK:
Complete Your Classic - ARB 4x4 Accessories
EDIT FOR LINK:
Complete Your Classic - ARB 4x4 Accessories
Started replacement of the rear upper fender skins. Both sides are out now and new ones ready to be tacked in.
The spot welds were a super blast to cut out.
Not.
Not.
And started getting rid of the bad outside rocker panel on the passenger side. Have the new one on hand to put in, just need the all elusive "more time" I here people talk about.
oooo I need to do this to mine, both rocket and well. Where be the pieces parts from?
I got these panels (top fender skins and rocker panel) from real steelife cruiser parts. Just Google them, so far I'm pretty happy.
Very welcome. My local cruiservice restoration shop said they have the best quality panels out of anyone they have tried. Said they are the closest to spec.
My local cruiser whisperers are extremely expensive, i use them as a knowledge resource, not a labor resource haha.
rkymtnflyfisher
Trout Bum
I am so glad I am done with that part of my build. It brings back horrible memories.
