I think I like Solidworks the best for 3D modelling probably because I have the most seat time with it. And AutoCAD for 2D. Sorry for the hijack y’all!
Last edited:
CruiserCult 40 Series Product offerings
- Thread starter Cruiser Cult
- Start date
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.
Cruiser Cult
Supporting Vendor
- Thread starter
- #322
Hey all!
Happy to say our partnership with CityRacer is continuing and another run of these in the works. We should have them done soon and available on both store fronts.
Happy to say our partnership with CityRacer is continuing and another run of these in the works. We should have them done soon and available on both store fronts.
Cruiser Cult
Supporting Vendor
- Thread starter
- #323
Holiday sale going on now through Monday 5/27.
Up to 50% off the site
Memorial Day Sale
Limited Time Sale. Up to 50% Off. This weekend only. Sale runs through 5/27. Discounted prices will show automatically in your shopping cart.
cruiser-cult.myshopify.com
Cruiser Cult
Supporting Vendor
Picked up a new gas cap for the 40. Thanks for the awesome discount!
-Dave
-Dave
Cruiser Cult
Supporting Vendor
- Thread starter
- #326
Thank you for the support Dave! Really appreciate it and happy cruising.
1911
chupacabra
Took advantage of the sale and got a 40 radiator drain valve; I have wanted one of these for a while. Thanks for the sale!
Cruiser Cult
Supporting Vendor
- Thread starter
- #328
Woohoo! Thank you for the support! I love that valve and I hope you do to. Draining the coolant is no big deal or mess now.
Cruiser Cult
Supporting Vendor
- Thread starter
- #329
One quality item at a time.
We always strive for top notch quality parts and customer service. We ship orders 1-2 times a week.
Thank you all for your continued support.
We always strive for top notch quality parts and customer service. We ship orders 1-2 times a week.
Thank you all for your continued support.
Cruiser Cult
Supporting Vendor
- Thread starter
- #330
New bushing coming soon! 
This is a little replaced bushing but plays a part in slop of the steering shaft. I know it’s a losing battle with 40s, but every little bit helps to tighten things up.
This is a little replaced bushing but plays a part in slop of the steering shaft. I know it’s a losing battle with 40s, but every little bit helps to tighten things up. 
sleepycruiser
I will get by….I will survive -Touch of Grey LC200
@Cruiser Cult I am likely going to replace my radiator. When I am ready if I message you can you tell me if the drain you sell will work on the radiator?
Might also get the fusible link.
Might also get the fusible link.
Cruiser Cult
Supporting Vendor
- Thread starter
- #332
Sure thing! We are here and always happy to help.
Cruiser Cult
Supporting Vendor
- Thread starter
- #333
Prototype snapped in oh so nice. Going to send one to @Kringle for testing These will pair nicely with the outer rubber bushing we are making with @CruiserTrash
These will pair nicely with the outer rubber bushing we are making with @CruiserTrash
Cruiser Cult
Supporting Vendor
- Thread starter
- #334
Added a variant on the slave cylinder heat shield. I found out there was a bit of an interference issue with a column shift rod at a point in it's range of motion. So I modified it. The body of the cylinder is still protected with this. We have one in stock now (more on the way) and floor shift variants in stock as well. HERE
The body of the cylinder is still protected with this. We have one in stock now (more on the way) and floor shift variants in stock as well. HERE
Cruiser Cult
Supporting Vendor
- Thread starter
- #335
Gauging interest in Viton rubber seals for the early sender units and fuel filler neck gasket (up to around 1965). We can offer these at $15 each and made by our local gasket maker. This is with a conservative 20 piece initial run. If we get a larger batch made the price would go down for each, but not sure on interest. We are going with Viton for its compatibility with ethanol (now very common in gasoline).
We can offer gaskets for the newer 40s with the three hole mount filler necks and sending units as well if there is interest.
We can offer gaskets for the newer 40s with the three hole mount filler necks and sending units as well if there is interest.
Would be interested for my 66.Gauging interest in Viton rubber seals for the early sender units and fuel filler neck gasket (up to around 1965). We can offer these at $15 each and made by our local gasket maker. This is with a conservative 20 piece initial run. If we get a larger batch made the price would go down for each, but not sure on interest. We are going with Viton for its compatibility with ethanol (now very common in gasoline).
View attachment 3690576
We can offer gaskets for the newer 40s with the three hole mount filler necks and sending units as well if there is interest.
Cruiser Cult
Supporting Vendor
- Thread starter
- #337
Cool! I’ll work on sets for the newer tanks.
Yes I’m in for a set.Gauging interest in Viton rubber seals for the early sender units and fuel filler neck gasket (up to around 1965). We can offer these at $15 each and made by our local gasket maker. This is with a conservative 20 piece initial run. If we get a larger batch made the price would go down for each, but not sure on interest. We are going with Viton for its compatibility with ethanol (now very common in gasoline).
View attachment 3690576
We can offer gaskets for the newer 40s with the three hole mount filler necks and sending units as well if there is interest.
kunzma
SILVER Star
I'd be in for three of the 4 hole filler neck seals.
tahoe40/45
SILVER Star
Im in for a few sets
