Builds AK HJ-75

[coldtaco]

Using grease didn’t work

 

[bcsteel]

More bread. I used a marble rye, very delicious, Impressive how much can fit in there. Put a socket on an extension backwards and pushed as much in until it you could use a dowel. I just couldn’t find a proper fit.

 

[2fpower]

Have you tried to soak it in some penetrating oil first? Kroil is my favorite....pricey, but works amazing. If you could tilt the engine forward so it is soaking in a puddle of it, that would be best.

https://www.amazon.com/Penetrating-Spray-10oz-Can-Single-Penetrant-KS102/dp/B00GM6NQLG/ref=asc_df_B00GM6NQLG/?tag=hyprod-20&linkCode=df0&hvadid=642868836410&hvpos=&hvnetw=g&hvrand=13757194457745417314&hvpone=&hvptwo=&hvqmt=&hvdev=c&hvdvcmdl=&hvlocint=&hvlocphy=9023909&hvtargid=pla-1950010544571&psc=1&mcid=d8603ac3f35f354f96a2d23554814b23

 

[coldtaco]

Once I blew the seal out using grease I figured going back to bread wouldn’t work. So dremel tool and cutting disk. The outer ring still won’t come loose with 4 cuts. I guess I have to keep working on it

 

[coldtaco]

Finally out, lots of rust on the surface

 

[renago]

if it was mine , I would grind out Rho se small parts

 

[coldtaco]

New bearing installed

 

[coldtaco]

Bell housing trimmed to fit.

 

[coldtaco]

Different breather installed

 

[coldtaco]

Well, that sucks. Broke the wires off the tach sensor/pick up. Anyone know the part number? I can’t find it on toyodiy. Anyone have a spare ? Anyone successfully repaired one of these?

 

[Owyhee Jackass]

Ben had an issue with his a while back, not sure if he fixed or replaced, but the discussion starts here:

Builds - 1988 BJ74 “Number 1”

@FJBen does the steep climb about halfway through still have pretty deep holes? Got some three wheelin’ action in my 60 a couple months back on that spot. I went out with a buddy who just bought a new Wrangler and I was trying to get his feet wet on an easy scenic trail - he wasn’t thrilled...

forum.ih8mud.com

And this came up too:

15% Off on $338.55| 8318060040 Toyota LandCruiser BJ70 BJ61 BJ60 RPM Revolution Detector Sensor Sender Genuine| Free Statewide Delivery in Australia

Special Offer for Australia: Shop Now for Only AUD$ 338.55 and Get an Additional 15% Discount. Free Shipping on Orders Above $50

www.cerolauto.com

 

[jblueridge]

What the heck did Toyota name it in the parts catalog?

 

[AirheadNut]

Looks like it is 83180-60040 Detector Assembly, Revolution.

 

[jblueridge]

Thanks for that.
Same for my BJ74.

 

[Owyhee Jackass]

Looks like FJ60 and 62s used the same part.
If you don't want to pay the premium for the Aus one, you should be able to find a used one I'd think.

 

[coldtaco]

ordered one from cerolauto. $177.00 plus free shipping ordered some other parts.

 

[FJBen]

ordered one from cerolauto. $177.00 plus free shipping ordered some other parts.

Mine broke as well. I was able to cobble it together with some epoxy. No idea how long it will last but for now it’s working.

 

[coldtaco]

Mine broke as well. I was able to cobble it together with some epoxy. No idea how long it will last but for now it’s working.

I've seen replies that say you can dig into the top with a soldering iron enough to get enough wire to solder the wires together again. Then fill with silicone or something stronger to stabilize that area.

 

[FJBen]

I've seen replies that say you can dig into the top with a soldering iron enough to get enough wire to solder the wires together again. Then fill with silicone or something stronger to stabilize that area.

That’s what I did. It’s not pretty but it works.

I had to use a razor and pick to clear it out.


Would be worth it to have a spare.

 

[coldtaco]

This was two days ago ready to install,