which

Hello, new to this corner of the forum, coming from a 100 series but want more room so looking into building a troopy. Can some of you who know what's up chime on on the merits between the two of these? One is a 1FZ with 250k miles, no rust or mods. Super clean in TX. The other is a 60k mile 1HZ...

I need to hang a new Vevor air hose reel on the wall in my shop, not sure which type of fastener to use. I have 3/8" x 3-1/2" lag screws with washers, or these new Simpson WS22 x 4” Timber Screws. I have plenty of both. Reel weights 23 lbs but is also subject to being tugged on to deploy the...

I am looking for a replacement fender for my 96' and noticed on Partsouq that there are two variations. Part # 5380160483 and 5380160223. One comes with over fender and mud guard and side step. I assume it is the one without. Amayama seems to have both available (fingers crossed) These are...

I've read some wrenching forums where people say 1/4" drive for everything interior, 3/8" for everything under the hood and 1/2" drive for everything under the vehicle. But I've always wondered if there's a set of guidelines outside of that. Obviously wherever you can fit the ratchet matters and...

a new with original hardware TT hidden winch tray for 95-97 fZJ80 will fit 91-94 with 95-97 front oem bumper. Mounted never installed winch Asking 350.00

Currently own: 2006 LC with 260k miles. Basically stock. Has been in family about 5 years, one of my kids drove for a bit. Needs Basically a full refresh. Ball joints, tie rod ends, suspension. Condition is fair. Can purchase from ole Dad. 2000 LX with 140k miles. One owner. Always...

I have taken off the OME suspension that was on my new to me 200 swapped my BP-51 on it. I’m going to sell the rake off parts but I don’t know exactly what rear springs these are: 722X? My guess is 7220 or 7222.

I had a 100 years ago (2000 LC) which was great. Now I’m looking to get back into one. My usage would be a daily driver 90% of the time (usually 5-6k miles per year). Then family camp trips, which would typically be fine in a stock rig with minor mods like roof rack and rear storage. But a...

Which CVJ axle should I get if I have a simple 1" coil over type lift. I have the Bilstein 6112 ride height adjustable coil-over setup in the front. This really is not a lift as all it does is move up the ride height within the stock travel. They have a "No Lift - Stock Angle" option and a...

I'm currently running the King 79s. She's a heavy girl. I have: Front and rear steel bumpers Winch Rear tire carrier Rear swingout Full drawer system Heavy roof tent 8 Gallon water tank Solar panels ...and more stuff I'm not thinking of Front pressures are dialed in using the stock LX...

They’re both at large franchise dealerships and have allegedly been reconditioned

Rebuilding my 10/74 transfer case (4speed) and some how lost track of which way the speedometer drive gear was placed on the output shaft? What direction should the output shaft be turning going forward in corilation with speedo driven gear. I realized that it could be turning in reverse if...

Hey Cruiserheads, Please post up your preference for our annual X-Mas party at my house in Abby. More details to follow on menu, times, etc. December 9 December 16 I can also do a Sunday if there is lots of preference for that (Dec 10 or 17).

Thought I'd bounce this off the experts as I'm sure I'm overlooking some things. Which one should I keep? Both are my preferred color (galactic gray) and rust free. I'm very familiar with the differences by year, but not sure how much all of the repairs and services completed on the '99 should...

02/69 fj40 My signals are still wonky. I know the grounds are good, all the lights work in some fashion. I’ve changed the switch to new oem. One side blinks, the other stays on (with the signal lever). The hazard switch used to make most of them flash and now it doesn’t. It hummed a couple...

Hey all, I've just rebuilt my handbrake assembly with a Terrain Tamer kit, and had a quick question regarding the handbrake dogbone. In many videos and images I've seen the dogbone as shown below.... The poky bit on one side points out, as shown in the red circle. On my 450, the old gear...

Trying to diagnose a few issues. I have an ultragauge. Does anyone know which sensor it pulls its engine temperature from? I thought it was the forward most sensor, but after replacing that sensor with a new OEM one, I have my doubts. The engine temperature is actually about 186. It will...

I have a new LS1aluminum 5.7, a 100k mile aluminum 5.3 already DOD deleted and ready, and a new iron 6.0. The 4l80 and rebuilt T-case are already installed and new drivelines made and installed. This will be for sale once finished, and I'm curious what more people would want?? Basically rust...

My son now has his permit and is constantly asking for our 2000 cruiser. So, we’re in shopping mode. But, he’s also asking what series most UC member own. Well, let’s find out. I know many of you post a signature with this info, but a poll will give the basics. if you like, leave a comment on...

Hello everyone, I want to put air conditioning on my '88 FJ62, it would be nice to find a ready-to-fit kit but I don't think there is, so I try to put various parts together. I can't find a condenser that has the right dimensions, can you tell me which one from which car I can use? Grazie