which

Good Afternoon Group, Working with a forum member on a build, but wanted to get some opinions, comments and advice on this. With the new 2017 LC200: I am going to install the Icon Coilover Stage 3 or 5, not sure yet, but regardless looking to lift the vehicle give it a more aggressive yet...

Hey folks. Thanks for the help my search grew tired. Which wire do I tap to run the hot lead to winch cut off so power is cut by the ignition. And where is it located. Thanks. Diagram is mia

I know one side is left hand and one side is ride hand threads which is which coming up empty on searches Thanks

I currently have a 2wd 2010 sr5 runner with 135k miles and am ready to upgrade to a 4wd model. I don't do a ton of off roading, but would like to start. I'm in AZ, so weather is not usually a factor. Would li,e to install a leveling kit at the very least, and run 285's or maybe a little bigger...

Hey All, My birfs started to clunk a bit while in low range,so I want to change them, but cannot find trusted info whether they are long or short.I could buy flanges as well but do not want to spend 100$ more just for that. Car is 93 model year, actually built 12/92.It has ABS and locked...

I have a LX450 (1996) and she needs a new bumper. As I am based in Africa I have no need whatsoever for a winch - in Africa one can always find 10 strapping lads ready to give a push for a few bucks a head. I have only needed a push once in last 10 years... I do like the TJM T17 but it has a...

Hi everyone. I'm the owner of a new-to-me 1996 Land Cruiser, which I am trying to piece back together. Some things were missing or broken, and one that I am a bit confused on is the correct part number for the rear mudguards. In various searches, I have come across a few different part numbers...

I have never worked on or owned a tacoma. I have been tossing up the idea of owning a Tacoma. I install networks. So that can require caring a ladder, part supplies and so on. I do not want a stick shift because traffic in Seattle is hell meaning...lots of shifting doing 15 mph on I-5. How...

So if you'll notice in the picture I have two starters.... I believe the smaller of the two is a 1.4 OEM and the bigger is labeled as a Denso reman. Which is the 2.0. Have two cruisers at the moment and wondering which is better to rebuild first to put on my daily. From everything I have read...

I have been searching for seats for my 80. Probably going to make mounts and do something late model. Anyway last night i saw this LX450 with these seats. Went by before work and the guy said the seats were gone, obviously. Whoever got them scored some NICE seats. Hopefully someone here got them.

I searched the manual and can't find it. I was wiring in my aux white switch and I think I blew the fuse I tried other functions on the fuse that seemed like it might be it but no joy

I need to change the oil on my FJ 40's diffs, 3.70. Which Oil should I use....Kindly guide... Thanks

My shop has narrowed down the shifting issue to a bad solinoid. Can some one tell me which one this is. I have a pict of the one he says needs to be replaced but can't figure out how to upload the image. I can email you guys the pict if someone can send me their email address. Or a link...

So I just picked up my first Land Cruiser 100 series and I am looking at trading my trailer for a different one. I currently have a 1942 Willys MBT that is pretty stock. It rides on a slightly wider axle than normal to match a Jeep TJ, but I still have all the stock stuff. The PO cut out the...

Long story short I am new to the cruiser thing, I've always had modified Jeep Cherokees (I know, bad word!) but now am the proud owner of two Cruisers! I have an '89 FJ62, and as of last night an 85 FJ60. The FJ60 is obviously a manual 4spd, but has an overdrive, question is what trans is this...

I have an OME steering stabilizer enroute to me. I've done some searching but I can't seem to find a recommendation for a specific tie rod puller to use for removing the old stabilizer. Seen the OEM and the OTC brands recommended, can anyone give me a model number for one that will work?

So I haven't had an oil pressure gauge in my cruiser for ever, a couple years ago I tried the stock sender and one for the 6BT, if I recall the cummins sender put the needle full stroke, I turned it off quick, the 80 series wouldn't hardly budge it (checked with the 6BT after to make sure I...

Fzj80(not locked) or Fj100(rear locked). Will be used for now as a dd and camping rig. Assuming mileage, maintenance, and condition are all comparable. Which one to go with when considering reliability, and off road ability (again not a tripple locked 80).

Hello team, I have been researching a lot about the correct Oil for the 1HD-T engine. Initially the car was using Valvoline full synthetic 15w40 oil. I changed it to Phillips 66 15w40 semi synthetic oil, and felt like a little difference on the behavior of the car when I accelerated. Like a...