Builds What's a Parts Guy to Do?? (3 Viewers)

[TRAIL TAILOR]

Guys, I'll look at trying to make one from a grommet and silicone tube. If I like the way they turn out they will be yours..

J

 

[TRAIL TAILOR]

Reevesci's got the right parts.

They are not available separately from the harness they came with.

What would I use? Not sure. Never had to find a replacement.

I can do some searching and see what I find.

I doubt they are available either but what about a Camry Wagon?

J

 

[sschruff]

hah! i don't think J's planning on parting with the new ones....have a feeling I'll be going the used route on these. I know that Tor couldn't even find one of the part numbers at all...per CDan the other hasn't been available for a while.

Maybe Onur is feeling extra nice and will chime in with the part #'s. Won't hurt to try to find them. . .eh?

 

[Joe_E]

K - roger that and no worries. Your need is a necessity, mine is obviously OCD =) If J's willing to give them up, they're all yours, buddy. If you can get me the part numbers, I'll put some feelers out for both of us.

First online Toyota site i pasted it to said they were available for $8.67.

82819-90A00

 

[OGBeno]

They all say that.

Online sites are like women when you first start dating them: They say everything you want to hear!!

 

[Joe_E]

The moose says you're closed, i say you're open.

 

[RodrigzCrzr]

First online Toyota site i pasted it to said they were available for $8.67.

82819-90A00

If they do sell them I'll take two.
Or you can guide me as to where to order from.

 

[OGBeno]

They are discontinued. You cannot get them.

 

[NCFJ]

I look forward to seeing this motor at home in the frame rails. Amazing how just a never ending stream of parts can be such porn. Lord knows I am not a huge fan of the tractor motor but damn Onur, that thing is beautiful, very tasteful.

 

[RodrigzCrzr]

:-(

 

[OGBeno]

Just a few small parts updates:

1. Finally made the decision on my rear bumper/tire carrier. Looking forward to the end result when it gets here. I'll post up the company that fabricated it as well as pictures when I receive it.

2. My good friend Steve M. and his son are coming over tomorrow to help me put the engine/tranny/xfer case together and I am actually hoping we can drop it into the frame rails and I can then spend my time putting everything together for a future initial start up.

3. And some parts procurement pics (mandatory I guess now):

New sleeve for the speedo gear:

New Clutch Hose from the hard-line to the slave:

New bolts for the transmission insulator to the H55F:

And the small brake hose near the master (the large vacuum line is unfortunately discontinued):

 

[vipergrhd]

Your killing me man,hahaha. More parts but where is the engine going to fire up? Just kidding take your time.

 

[jfnall]

This 60 is gonna be worth a 100k. I'd be afraid to drive it.

 

[OGBeno]

Well, unfortunately, due to some issues, the engine did not go in the frame yesterday.

That said, we did get a lot accomplished. My good friend Steve M and his son just in from Tuscon came over to assist as did bmacc.

Got the tranny mated to the engine. This sucker is long--69".

Also, did some small things around in the engine bay:

New grommet for the water inlet and outlet, installed the water valve and installed the L hose:

 

[OGBeno]

Next was to get the leaking PS gear box off as well as the intermediate shaft.

PS box is going to West Texas for a reseal.

New intermediate shaft has been ordered from Toyota.

 

[GLTHFJ60]

You consider upgrading to an 80 series box or sticking original for that too?

 

[OGBeno]

Then we went to work on the rear bumper. A real rear bumper/tyre carrier has been ordered from a MUD fabricator. I only want the best for this and this fabricator seems to be the person for it. Looking forward to getting a final product.

The hitch receiver had been welded to the frame unfortunately. So a lot of grinding and cutting. Then the bumper bolts were rusted to the nuts so they had to be ground off too.

 

[OGBeno]

You consider upgrading to an 80 series box or sticking original for that too?

Original will be fine for my application purposes.

 

[DanS HJ-45]

My goodness that engine/trams/Xfer looks good all together!

Take a good camera, get good pics, frame it.

Can't wait to see the rear bumper! Are you going to clean out the passage behind the wiper motor/access panels while its relatively easy to get to?

Dan

 

[Major Nelson]

Engine looks so nice. You should just mount it somewhere in your house so that you can just stare at it all day long. Beautiful work.