What have you done to your Land Cruiser this week? (33 Viewers)
- Thread starter IH8MUD
- Start date
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.
rrv333
SILVER Star
Knuckle rebuild. She's fighting me every step of the way. If it's not the upper cap, it's the lower cap. Then my 54mm socket was too shallow to reach the inside nut and the list goes on and on. Having a blast though.
thecrazygreek
A.K.A. TheCraftyGreek
There's no beer like Oregon beer...
The most breweries.. the best brews. The fj40 beer is dead guy...
The most breweries.. the best brews. The fj40 beer is dead guy...
Got to love NW beer!!! Deschutes... Crux....
77mustard40
SILVER Star
Replaced the rear spring bushings, they were reduced to granola. First time to work on my own suspension. I’ve recently come to the conclusion that I should never let someone else work on my truck, no matter how daunting the task and lack of experience.
The retaining bolts for the pins were way too long and had run through the bushing flange and all the way into the springs. I know, nice. Takes a second to use the correct hardware.
The retaining bolts for the pins were way too long and had run through the bushing flange and all the way into the springs. I know, nice. Takes a second to use the correct hardware.
First of the small bits have been painted! That's Horizon Blue for a '67. I see light at the end of the tunnel 
thecrazygreek
A.K.A. TheCraftyGreek
We have color!!! shot the firewall, cowl, dash and rear fender wells. The rest of the floor will be tinted raptor liner. Tranny hump will be glossy as well.
Camera doesn't pick up the blue, looks more grey in the pics. LOVE this color.
Its my version of Horizon Blue.
Camera doesn't pick up the blue, looks more grey in the pics. LOVE this color.
Its my version of Horizon Blue.
Finished my TBI install and took her for a test drive. Very pleased with the result.
thecrazygreek
A.K.A. TheCraftyGreek
What tbi system did you use?
Any write up on it??
I'm going to install a howell system in the next couple months.
I put it together following Downey's instructions. I was going to make a harness, but found a Howell harness and computer on ebay. I modified it to have computer controlled spark advance rather than the vacuum advance. I figured if I was adding a computer I wanted to take full advantage of it.
I'll start a write up this week on the install since I know from my own research it would be nice for more information.
Hit my shop door with my Toy.
I keep my Cruiser in my work shop that has swinging barn doors.
It was colder than kraut so I just opened the doors with out bothering to latch them open and jumped into the Toy and pulled in.
A gust of wind caught the left door and it swung in hitting the left side of the Cruiser somewhere near the rear tire bending the siht out of the door and tearing it half off the hinges.
I looked all over but couldn't find any new marks on my rig so spent the next few hours in the blankety blank cold rebuilding the blankety door.
I keep my Cruiser in my work shop that has swinging barn doors.
It was colder than kraut so I just opened the doors with out bothering to latch them open and jumped into the Toy and pulled in.
A gust of wind caught the left door and it swung in hitting the left side of the Cruiser somewhere near the rear tire bending the siht out of the door and tearing it half off the hinges.
I looked all over but couldn't find any new marks on my rig so spent the next few hours in the blankety blank cold rebuilding the blankety door.
oregon fj
Serial rescuer of old vehicles
Take me to the river,
drop me in the water.
Take me to the river,
dip me in the water
Washing me down, washing me down
Looking awesome! Did you do the paint yourself?First of the small bits have been painted! That's Horizon Blue for a '67. I see light at the end of the tunnel
View attachment 1678026View attachment 1678031
Picked up some designated parking signage
thecrazygreek
A.K.A. TheCraftyGreek
Shot the raptor tinted liner on the inside floors!
Then for fun I assembled one of the running boards. First time I've built one of the older versions.
You can see the true blue color much better on the running board pics.
Then for fun I assembled one of the running boards. First time I've built one of the older versions.
You can see the true blue color much better on the running board pics.
You're actually planning to STEP on those nice running boards?
This has always been my constant dilemma - I'm afraid I'll make my truck so pretty I won't want to touch it. Hopefully you don't share the same disease - because yours is looking great!
cruiserkreutz
SILVER Star
Nice! Did you need to use a dented side pan to get enough clearance for the HEI distributor?
Bent and welded an ugly but (hopefully) effective fan shroud with clearance at the bottom for the Saginaw steering shaft and the lower radiator hose. Not exactly a work of art, but pretty please given it was bent between a couple of 2x4’s, flanged with vice grips, and body worked with a dead-blow mallet.
Still debating dropping to a 17” fan - made clearance as wide as I could on my current 18” fan, but still only have a bit over a half inch between the shroud and the blades. As you can see, I ran out of space to make the hole any bigger...
Next I figured out my power steering hose routing to and from the cooler. To the perceptive person who will chime in - yes, I had high pressure and low pressure reversed in the picture - I fixed it.
And lastly, I created more work for myself.
PSA - when your bib isn’t bolted in, and your futzing around with hose placement, keep your headlights away from the tow hooks!
Still debating dropping to a 17” fan - made clearance as wide as I could on my current 18” fan, but still only have a bit over a half inch between the shroud and the blades. As you can see, I ran out of space to make the hole any bigger...
Next I figured out my power steering hose routing to and from the cooler. To the perceptive person who will chime in - yes, I had high pressure and low pressure reversed in the picture - I fixed it.
And lastly, I created more work for myself.
PSA - when your bib isn’t bolted in, and your futzing around with hose placement, keep your headlights away from the tow hooks!
Last edited:
I fixed an oil leak. My pan was leaking at the drain from a dimple in the area of the slot. After cleaning and roughing up the surface, I used JB Weld to build up the area and then sanded it back down flat. A little fresh paint, and no more leak.
