Don't have a cleaver name for it I've abandoned my buggy project and just decided to sink all that money/ parts I've been saving into my 40.
Here's the truck as it sits now:
Just ordered a butt-load of parts, most everything is en-route
Parts list:
* STaK 3 speed case
* Ford 9" rear with TNT Customs truss, disc brakes, True Hi9 center section w/ BTF skid, and Moser 35 spline shafts.
* RamJet 350 w/ TH350 trans
* Art Carr shifter
* FJ 60 front axle with 30 spline Longfields, Trail Gear 6 shooter knuckles and PSC hydro assist, 3" wheel spacers to match rear width, BTF diff protection.
* Beard racing seats w/ bench seat in the rear (for the kiddies!)
* 5 37" Iroks on 32 bolt beadlock rims
* High angle driveline shafts w/ 1350 CV long slip front
* Warn 8274 winch
* Full Detroits f/r w/ 4:88 gears
The build:
* Rear: Wishbone 3 link in the rear with QA1 chromo 1.25" heims, Lowers will be 2" O.D. .250 wall DOM. Upper wishbone will be 1.75" .250 wall DOM. Stnd alone Ebach coil springs using BTF coil buckets. Rear will probably be strecthed 5-8 inches as well.
* Front: I'm going to leave the front Leaf sprung right now, if the 60 front doesn't hold up I might build a high 9 steering axle for it.
* Re-doing the cage and doing a family style cage that's more accomidating for the rear passengers as well as front and rear bumpers with a swing away rear tire carrier, tube front fenders, and rock sliders.
This thread might be un-eventfull for a while, getting married this weekend and will be out of town till May 10th! Hopefully when I get back I'll have some parts waiting on me and I can work on it!!! I'll be posting lots of pics!
Jason
Here's the truck as it sits now:
Just ordered a butt-load of parts, most everything is en-route
Parts list:
* STaK 3 speed case
* Ford 9" rear with TNT Customs truss, disc brakes, True Hi9 center section w/ BTF skid, and Moser 35 spline shafts.
* RamJet 350 w/ TH350 trans
* Art Carr shifter
* FJ 60 front axle with 30 spline Longfields, Trail Gear 6 shooter knuckles and PSC hydro assist, 3" wheel spacers to match rear width, BTF diff protection.
* Beard racing seats w/ bench seat in the rear (for the kiddies!)
* 5 37" Iroks on 32 bolt beadlock rims
* High angle driveline shafts w/ 1350 CV long slip front
* Warn 8274 winch
* Full Detroits f/r w/ 4:88 gears
The build:
* Rear: Wishbone 3 link in the rear with QA1 chromo 1.25" heims, Lowers will be 2" O.D. .250 wall DOM. Upper wishbone will be 1.75" .250 wall DOM. Stnd alone Ebach coil springs using BTF coil buckets. Rear will probably be strecthed 5-8 inches as well.
* Front: I'm going to leave the front Leaf sprung right now, if the 60 front doesn't hold up I might build a high 9 steering axle for it.
* Re-doing the cage and doing a family style cage that's more accomidating for the rear passengers as well as front and rear bumpers with a swing away rear tire carrier, tube front fenders, and rock sliders.
This thread might be un-eventfull for a while, getting married this weekend and will be out of town till May 10th! Hopefully when I get back I'll have some parts waiting on me and I can work on it!!! I'll be posting lots of pics!
Jason