PabloCruise
SILVER Star
O-K, who was writing about a different seal used between the 2 different 34mm shaft split cases?
Will the different seal required for the new half case be compatible with his gears?
Delancy's NEW 76 PIGGY ??? (1 Viewer)
- Thread starter montyorpenn
- Start date
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.
O-K, who was writing about a different seal used between the 2 different 34mm shaft split cases?
Will the different seal required for the new half case be compatible with his gears?
Is this the correct front cover and do you still need one?
I don't know.
I don't think so, but thank you very much.
Hour and a half on local 80 lift, so no one thinks I'm completely incompetent.
Always funny to see the JGL-ish grin after lifting someone's rig. Hahaha.
If you end up requiring one and this one will work, send me an address to send it to and it’s yours.
Thanks again, J Mack.
Cruiser karma is strong here in the Sty, as you've proven, and are relatively new.
Very cool place and I hope that these Pigs were all endowed with appreciate as we do, because they may not exist without.
Going back to the seats.
Has anyone ever seen a rear bench in any vehicle that had ABTS at all three seating positions?
Thinking about finding means to integrate into the rear fold down.
Would powered front seats be that big of a deal?
I do not want them, but that appears the only configuration for the GMC seats with the flat railed base and ABTS. Can't find the same ABTS in anything but tan leather, either.
These seem a very viable solution, but they're not in line aesthetically with the balance of the planned interior.
Hoping to find in manual, black (for black belts. Thinking recovering wouldn't be an issue) but don't know if they'll aesthetically integrate.
Opinions?
Has anyone ever seen a rear bench in any vehicle that had ABTS at all three seating positions?
Thinking about finding means to integrate into the rear fold down.
Would powered front seats be that big of a deal?
I do not want them, but that appears the only configuration for the GMC seats with the flat railed base and ABTS. Can't find the same ABTS in anything but tan leather, either.
These seem a very viable solution, but they're not in line aesthetically with the balance of the planned interior.
Hoping to find in manual, black (for black belts. Thinking recovering wouldn't be an issue) but don't know if they'll aesthetically integrate.
Opinions?
Sounds reasonable to me. It's already apart, might as well make it new.
PabloCruise
SILVER Star
Whoomp! There it is...
tucker74
Moderator
Really not much to rebuilding a split case, just some bearings, seals and gaskets ... have to do most of the last two just to install it. Kurt & Georg had "kits" in stock a few weeks ago
Tucker
Tucker
Any help in liquidating this locally would be much appreciated.
https://forum.ih8mud.com/sale-parts/798047-boulder-acc-rebuilt-pcd-4spd-split-case-1k-obo.html
Really not much to rebuilding a split case, just some bearings, seals and gaskets ... have to do most of the last two just to install it. Kurt & Georg had "kits" in stock a few weeks ago
Georg is shipping out today.
Robbie's going to blast the cases which I was honestly considering doing to the PCd very early on in the pre-build consternation stage.
Had decided I'd live with it, kind of like I've decided to give up on freeborn red head paint.
PabloCruise
SILVER Star
I am happy to post in the Horsetooth 4 Wheelers section here: https://forum.ih8mud.com/co-wy-hors...r-acc-rebuilt-pcd-4spd-split-case-1k-obo.html
And in the RS forum: https://forum.ih8mud.com/co-wy-hors...r-acc-rebuilt-pcd-4spd-split-case-1k-obo.html
Good Luck!
automatic butt thermal sensors?
Dirty, dirty, dirty....
All Belts To Seat, like the domestic truck seats some run in the front, with the integrated seat belt.
Have you spoken to Robbie, yet?
Onur's stash of pistons were all within 1.5 grams of one another, so going in the freezer this weekend.
To fulfill my self prescribed obligation to his sending, have a resource for 2F flat tops in all OS dimensions and awaiting confirmation of total cost.
No, this is not a classified ad nor a Group Buy but if anyone is interested in OE OS 2F flat top pistons sets, will have a shipment coming and it's be easy to add to the order.
Estimated Cost $380 for six.
Pay for via Paypal. Allow 6-8 weeks delivery.
I'm faulty certain that multiple sets will result in a greater discount, reason for posting and for consideration if interested.
Full disclosure.
These are still available from Toyota for $434.00.
If you're on a terrorist watch list or of ME origins, it'd be my pleasure to receive yours and forward to you, because they do come from an Iranian postal service and the contents will be searched at Customs.
Not illegal. Not finding terrorist and the Paypal goes to a Norwegian.
To fulfill my self prescribed obligation to his sending, have a resource for 2F flat tops in all OS dimensions and awaiting confirmation of total cost.
No, this is not a classified ad nor a Group Buy but if anyone is interested in OE OS 2F flat top pistons sets, will have a shipment coming and it's be easy to add to the order.
Estimated Cost $380 for six.
Pay for via Paypal. Allow 6-8 weeks delivery.
I'm faulty certain that multiple sets will result in a greater discount, reason for posting and for consideration if interested.
Full disclosure.
These are still available from Toyota for $434.00.
If you're on a terrorist watch list or of ME origins, it'd be my pleasure to receive yours and forward to you, because they do come from an Iranian postal service and the contents will be searched at Customs.
Not illegal. Not finding terrorist and the Paypal goes to a Norwegian.
