Builds Benjamin’s 3D Prints Build (26 Viewers)

[suprarx7nut]

Guys. A little update: I received my PhD (Mechanical Engineering - Robotics), finally, this May. I am relocating to Michigan (Rochester Hills, north of Detroit) and starting my first real job as product development and research engineer early September. Sorry for not replying emails in a prompt manner. Don’t need to resend. I will get to each email or PM. I am still taking orders but in a slower pace since most of my printers are packed up. I am going to move all my 3d print equipment with me and set them up in the week of Aug 22nd.

Congrats, Doc! Very cool.

 

[jad05k]

@BenCC I saw this tray on an auction vehicle recently (on bringattailer). I’ve never seen this OEM personally but maybe it exists? If not, it could be a nice complement to the CD/DVD changer replacement.

 

[Live to Ski]

@BenCC I saw this tray on an auction vehicle recently (on bringattailer). I’ve never seen this OEM personally but maybe it exists? If not, it could be a nice complement to the CD/DVD changer replacement.

I actually have one of those.

 

[I Lean]

I actually have one of those.

Me too. I think it's currently out of the console, not in use.

 

[Formerjeeper]

I believe that's a factory part. There is one in my 2005 LC.

This should be the Toyota part number, but might be NLA:

5882360030​

 

[Formerjeeper]

Here is a used one if you really want it badly enough:

2000-2007 LEXUS LX470 J100 REAR CENTER CONSOLE COMPARTMENT 58823-60030 | eBay

Find many great new & used options and get the best deals for 2000-2007 LEXUS LX470 J100 REAR CENTER CONSOLE COMPARTMENT 58823-60030 at the best online prices at eBay! Free shipping for many products!

www.ebay.com

 

[jackhossross]

Bare with me here.

I have an overhead mount: M4V1.3

However I would like to fit the Toyota Tall Bush Buttons into the slots: Toyota Tall Skinny OEM Buttons

I would think a spacer/square could be attached to the overhead mount, into each switch location that would allow a snug fit of the tall skinny toyota switches.

Anyone have any thoughts?

 

[jad05k]

I never cease to be amazed by this group. Thanks. I searched this forum google and eBay stuff trying to find that and figured it wasn’t there, haha. Thanks and sorry to waste any of Ben’s time even looking at my original message.

 

[ClassyJalopy]

Bare with me here.

I have an overhead mount: M4V1.3

However I would like to fit the Toyota Tall Bush Buttons into the slots: Toyota Tall Skinny OEM Buttons

I would think a spacer/square could be attached to the overhead mount, into each switch location that would allow a snug fit of the tall skinny toyota switches.

Anyone have any thoughts?

The hole size in your mount is standard carling size. I have fit tall skinny Toyota size switch in a Carling hole by simply wrapping the outer edge of the switch in one layer of Tessa tape. It made the switch fit snuggly and not rattle at all.

 

[jackhossross]

The hole size in your mount is standard carling size. I have fit tall skinny Toyota size switch in a Carling hole by simply wrapping the outer edge of the switch in one layer of Tessa tape. It made the switch fit snuggly and not rattle at all.

Thanks for the insight, I will go this direction first.

Of course, wrap it in tape. My lack of innovation is appalling.

 

[jackhossross]

Mine required a layer of 3M double sided mounting tape and tessa tape, but they are in their positions nice and snug.

Thanks Ben for another great product. I need a few more, what is the status of getting on the wait list, if you are even taking orders currently with everything going on.

Cheers,

Jack

 

[audioviking]

Guys. A little update: I received my PhD (Mechanical Engineering - Robotics), finally, this May. I am relocating to Michigan (Rochester Hills, north of Detroit) and starting my first real job as product development and research engineer early September. Sorry for not replying emails in a prompt manner. Don’t need to resend. I will get to each email or PM. I am still taking orders but in a slower pace since most of my printers are packed up. I am going to move all my 3d print equipment with me and set them up in the week of Aug 22nd.

Congrats, Dr CC!

 

[mjcalderone3]

Make 37 Icon Compression/Rebounds Wheel Caps

1 Overview of the Final Product

View attachment 2485903
Photo credit to @larryt.



View attachment 2485902

2 Introduction

The caps work on Icon Compression/Rebounds wheels. Thanks to @Dparo. He mailed his wheel cap to me. With a couple of iterations, M37 finally has all its dimensions fitted with the wheel. You can reuse the sticker from the original caps.

View attachment 2485905

3 Purchase

$100 for a set of four caps plus shipping.

PM for Direct Paypal Payment.

I am interested in purchasing a set of these M37 caps. I just had some ICONS installed on my 2003 LX and the front two wheels need this solution to cover the hub. Please let me know how to purchase.

 

[Dparo]

Who makes your seat covers? Also the cup holder looks

@AlpineAccess

Escape Gear. Got them through Equipt. Sorry for the delay in responding.

 

[AlpineAccess]

@AlpineAccess

Escape Gear. Got them through Equipt. Sorry for the delay in responding.

No worries, I've had a set since May

 

[sunfic]

Working on this CD/DVD changer replacement:

is it ready? I wanna one.

 

[tim399]

A big thumbs up from Australia The colour difference is far less noticeable in person. Great work, thank you Ben.

 

[blacktimber]

I sent an email to Ben about 6 weeks ago hoping to establish an order for some of his 3D products for my lx470 and never heard back. In fact he never read my email. I see he hasn’t posted anything on this thread since august 18th. Anyone know if he is still in the 3D printing business?

 

[MongooseGA]

Guys. A little update: I received my PhD (Mechanical Engineering - Robotics), finally, this May. I am relocating to Michigan (Rochester Hills, north of Detroit) and starting my first real job as product development and research engineer early September. Sorry for not replying emails in a prompt manner. Don’t need to resend. I will get to each email or PM. I am still taking orders but in a slower pace since most of my printers are packed up. I am going to move all my 3d print equipment with me and set them up in the week of Aug 22nd.

I sent an email to Ben about 6 weeks ago hoping to establish an order for some of his 3D products for my lx470 and never heard back. In fact he never read my email. I see he hasn’t posted anything on this thread since august 18th. Anyone know if he is still in the 3D printing business?

Probably something to do with the above.

 

[Edcantera]

Probably something to do with the above.

I’m hoping that Ben has a good relocation and that we are all able to get back in line for some of his awesome products. I sent him a few PMs before reading his latest post. Now just waiting patiently for a reply.