What Did You Do with Your 80 This Weekend? (18 Viewers)

[sbman]

Anyone know the best product to use to seal up these trim bracket holes? They are leaking water onto my rear seatbelt bases, and I need to seal them up before putting the exterior trim back on. Thanks for any suggestions.
View attachment 1433959

If it's just for water intrusion, something like this?

3M All-Around Autobody Sealant 08500

 

[PolarRunner]

Where di you score these? Ive seen em on amazon for like 20. Im in dire need previous owner made a mess under hood.

Shop The Hillman Group 2-Count 1/4-in Zinc-Plated Standard (SAE) Regular Nuts at Lowes.com

Should be in the hardware section, probably near the all thread bins or along with the regular nuts, maybe one of the "specialty" nut drawers.

 

[NLXTACY]

Doing a complete brake job on @jaymar's 80.

 

[Dubbinchris]

Doing a complete brake job on @jaymar's 80.

View attachment 1434005 View attachment 1434006

Ooohhhh the DBS rotors.

 

[itbrokeagain]

I did this

 

[Dubbinchris]

I did this

View attachment 1434050

Stuck....broken...taking a break??

 

[NLXTACY]

Well crap. Looks like we might have a cracked spindle. Cracked or maybe grooved. Hard to really tell.

Opposite side has a very bad inner bearing.

 

[itbrokeagain]

Stuck....broken...taking a break??

Just trying a different line

 

[ExpoGeorgia]

Installed my Tough Dog 3 inch lift last night.. rides so smooth looks great. Just have the caster plates and adj panhard rods left

 

[TRAIL TAILOR]

Installed my Tough Dog 3 inch lift last night.. rides so smooth looks great. Just have the caster plates and adj panhard rods left

View attachment 1434080 View attachment 1434085 View attachment 1434086 View attachment 1434087

S, It looks great! Glad you like the ride. I love the foam cell shocks on the cruisers.

J

 

[NLXTACY]

Not much grease in the knuckle but at least it's not mixed with diff gear oil.

 

[PolarRunner]

You must love vanilla lattes.

Finished up my power steering pump replacement last night. Also swapped out the 2 hoses from the reservoir. Man, 23 year old rubber is really brittle and useless. Overall the job is quick and fairly easy if you have some mechanical skills. "Special" tools I found to be helpful, were a cheater bar (the handle to my jack) to tap on the back of the pump to coax it out and my DIY fluid filler set up. The rubber lines I replaced were hard as plastic. Also took the time to grind off the rust on the battery tie down bar and rust reform the J hooks. Painted any bare metal with protective enamel.
View media item 53356View media item 53357
Since I bought the cruiser, the engine side of the battery tray was torn from oil and grease and the hook being tightened into it. I thought about what I had on hand to reinforce the tray and cut up some holed metal bar and bolted it in. Works a treat.
View media item 53359View media item 53358

 

[RFB]

View attachment 1433709 Read up on my transmission issue here and found a few easy fixes! Made my day! I love this forum!

Also found some new front seats on CL for dirt cheap to replace the broken and torn up power leather seats in my 93. PO paid $1,400 for this set and he let it go for $300 with real Katzkin leather.

thats is a score, m really thinking recaro for the fronts

 

[RFB]

I got rid of the BFG Krawlers and replaced them with 37' Nitto Mud Grapplers. Krawlers are just way too soft for the heavy FJ80.

Grapplers sit about 1/2 taller and an inch wider.

Im looking to trade my beat 37 Mud terrains and was eyeing the grapplers, whats your total lift. suspension and body. and do you have massive wheel spacers?

 

[FJP971]

Installed some more sound deadener, replaced PCV grommet and had to dig out the bottom brittle piece with needle nose pliers, paid for my KISS drawers from @cruzerDave, and added some additional storage. I'll be spraying the interior with bedliner on Monday. Fridge will be mounted behind driver's seat for easy access on road trips.

Well it's not the best bedliner application job ever done but I think it will work. Sprayed some etching primer on the sound deadener to help adhesion. Spilled a little bit, splattered more than I anticipated, but it's not a show truck so screw it!

Alcohol rub down before it sets gets most of the splatter off. I added rubber granules for more traction, hence the bumpy look. Forgot to plug the few bolt holes I still need to use. Time to break out my new tap and die set!

 

[eurosonic]

Im looking to trade my beat 37 Mud terrains and was eyeing the grapplers, whats your total lift. suspension and body. and do you have massive wheel spacers?

check out my build thread in my SIG

 

[jbatx]

I did this

View attachment 1434050

Gonna need some touch up paint

 

[cody c]

I got rid of the BFG Krawlers and replaced them with 37' Nitto Mud Grapplers. Krawlers are just way too soft for the heavy FJ80.

Grapplers sit about 1/2 taller and an inch wider.

I can't get enough of those white spoke wheels, looks so good

 

[McGrinnan]

I am getting closer, hope to drive it Wed

View attachment 1433760

View attachment 1433761

If that's the 12 Valve 6bt I'd make sure you look up/do the killer dowel pin fix.....if not then that's very clean setup ya got there. Build thread?

 

[Seth_O]

Sounds like a trooper tank would hard to find, why not just weld up the hole?

I thought about that, but they didnt just punch holes, they completely aerated the tanks. Its too bad, 3-5 holes in each and all wallered out really big. Disgusting waste.

My next step is the Isuzu boneyard. Its a step up from the pick 'n pull. Since they disassemble and store, its more likely to have a good one still intact.