What did you do with your 60 this weekend? (20 Viewers)

[BGarcia88FJ62]

Preparing to properly center my old knuckles to the FJ62 axle housing I put together in 2019 (Leaking Axle Seals)
and remove and inspect rear differential replace a leaking rear pinion seal (Started leaking at some point on my way back from Tennessee last weekend)

 

[Godwin]

Ha! I hope the new bumper just magically attaches itself on your rig

Kubota magic

 

[LimuEmu]

Kubota magic


View attachment 2627931

NICE!!

 

[Godwin]

Bumper installed. A 4PlusProducts Kingdom bumper along with a rebuilt Warn 8274 with upgraded 6 hp motor. Still have to wire the winch but the heavy stuff is done.

 

[MoaByte]

You ought to consider bringing it out to Moab. We need studies on Collard Lizards and the Faded Pygmy Rattlesnake.

 

[4Cruisers]

You ought to consider bringing it out to Moab. We need studies on Collard Lizards and the Faded Pygmy Rattlesnake.

We actually saw one of those rattlesnakes on a hike to Broken Bow Arch, just as we were descending into Willow Gulch. From what I've read, those little suckers pack quite a punch. That's the only one we've ever seen.

 

[Godwin]

You ought to consider bringing it out to Moab. We need studies on Collard Lizards and the Faded Pygmy Rattlesnake.

If I only had the time.....

 

[87CRUSR]

Bumper installed. A 4PlusProducts Kingdom bumper along with a rebuilt Warn 8274 with upgraded 6 hp motor. Still have to wire the winch but the heavy stuff is done.

View attachment 2628112

Can you post a side view shot of the front bumper install? Curious about the clearances. Thanks

 

[MarkBC]

I moved it this weekend because we had to take a huge rotten balsam down in the parking lot. The good news is that after 6 months sitting outside over the Pacific northwest winter, there is no sign of any new rust on the roof or gutter seams. Progress is slow on this "resto" but the important stuff has to happen first. Would be nice to get it roadworthy sometime.

 

[YooperCruiser]

Wheeeled the pi$$ out of it. Spring wheeling can be a challenge but the cruiser did great and got through some stuff even my buddies double locked Jeep on 35's had to winch through. I did get stuck once and had to winch out but everybody got stuck there, that rut was super deep and we all got hung up. Had a blast but I often wonder if I should be wheeling this pristine, low mileage rust free 62 this hard.

Both Jeeps got stuck here, the cruiser chugged right up through it

 

[Godwin]

Can you post a side view shot of the front bumper install? Curious about the clearances. Thanks

Photos posted here 4PlusProducts Kingdom bumper - https://forum.ih8mud.com/threads/4plusproducts-kingdom-bumper.1247098/

 

[kirvesmies]

Wheeeled the pi$$ out of it. Had a blast but I often wonder if I should be wheeling this pristine, low mileage rust free 62 this hard.

View attachment 2628529
View attachment 2628530


Both Jeeps got stuck here, the cruiser chugged right up through it

View attachment 2628533
View attachment 2628535

yes, yes you should. cuz i doubt you'd ask the question regarding a woman

 

[MarkBC]

Had a blast but I often wonder if I should be wheeling this pristine, low mileage rust free 62 this hard.

Just keep the salt off it

 

[kirvesmies]

Just keep the salt off it

that should be easy, there's no salt out in the woods

 

[YooperCruiser]

Just keep the salt off it

It's never seen salt. It came from Cali and I store it away every winter in a heated shop. Woke up to 5" fresh snow this morning though so back it goes into the shop until the roads get washed clean with some good rain.

 

[diesellibrarian]

Cleaned up my grille....and my throttle body.

This is the BEFORE pic. Forgot to take an "after" but trust me: it looks much better now.

 

[ENDO]

Installed new headlight purchased from @cityracer . Love these lights easy to install plug and play.

 

[Ocho77]

Washed his and hers.

 

[dad4x4]

Took it around town for a while then filled up the fuel cans for the mower. I’ve put over 100 miles on it since the transmission rebuild and it drives great!

 

[jamesurq]

Lots of wiring....
Can anyone tell me where/what color to tap into the ignition circuit? I'm running a second battery with an isolator that needs the ignition to switch on/off.