Builds My Current Build-up (billy bad-ass)

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Sweet

Looks great, keep it up.


JR
 
thanks. My buddy did some photoshop to get me inspired
GreenCab.jpg
 
awesome thread!
been a lurker for a while, that photochop is sick!

what's left on your list of parts you need?
got any more photos of the motor installed?

what are you going to do under the main crossbar in the belly? take it out and go higher?

What are you gunna hang off the front of it?
 
awesome thread!
been a lurker for a while, that photochop is sick!

what's left on your list of parts you need?
got any more photos of the motor installed?

what are you going to do under the main crossbar in the belly? take it out and go higher?

What are you gunna hang off the front of it?

I still have quite a bit to get for it...I'm gonna order some airshocks for the rear tomorrow 18" travel
I don't have anymore pics of the engine installed other than what is up right now.
I still need a bunch of tube adapters

what are you talking about on the x-member? It is installed..It's totally flat

What do you mean hang off the front? Axle? FZJ-80 Winch? Warn 9500Thermo Bumper? Singer with fender protector that ties across the cowl and into the sliders
 
nice work on getting legit,

the truck is looking better and better
 
What do you mean hang off the front? Axle? FZJ-80 Winch?

vs .. ?

the 80 axle it's pretty fine .. but you really need it vs mini truck axle . ?
 
I've been busy this weekend
It turns out that you can flip the tierod on a -80 series axle to the front by reversing the trunion bearing plates and cutting the steering mount off the opposite side(it hits the caliper). I'm running full hydro now so I don't really have a need for the steering arm anyway
Picture001-6.jpg

Picture002-5.jpg

Because I know everyone loves pics of trucks on cinder blocks
Picture003-6.jpg

Ballistic Fab Coilover Mounts
Picture004-6.jpg

Picture005-3.jpg

Lower Link Mounts Tacked
Picture006-4.jpg

Oh Yeah, 26" above the ground
Picture007-6.jpg

Uppers Tacked
Picture008-4.jpg

Uppers On
Picture009-4.jpg

Front Near Completion(Hydro is lacking)
Picture010-4.jpg

Picture011-1.jpg

Back Under the Truck(Look at how close everything is...yeah, thats a T100 oil pan)
Picture012-2.jpg

Picture013-2.jpg

Picture014-2.jpg

Picture015-2.jpg

Picture016-2.jpg


The reason for no updates is b/c I have been busy building rigs for other people
 
saw the truck in person this weekend. looks good!




finally got mine to the muffler shop this morning, i think i have a line on the fold flat floor for your rig. i'll give you a call. dave
 
keep up the work. lookin' good.
 
Tonights Progress:
1. Get upper mounts designed and built...
Picture017-2.jpg

Here is the pass. side upper mount(it clears the d-shaft) This is the view from the bottom and no it isn't finished.
Picture019-2.jpg

Picture020-2.jpg

From Front
Picture021.jpg

Looking up(no guessets yet)
Picture022.jpg

Looking Forward from rear
Picture023.jpg



SWEET! Thanks man, I tried calling you earlier today..I had a ? But got it figured out
 
It si getting some...Like I said, it isn't finished yet...you can't tell but the bracket extends across the top of the frame rail to the other side. It also has guessets that tie into it.
 
10-4 Thanks


Tonight I got the other upper mount damn near finished and I got the first finished...I am gonna start on the lowers tomorrow...I figured out where they will mount though and it appears that I'll have clearance everywhere I need it.
 

Users who are viewing this thread

Back
Top Bottom