Builds Benjamin’s 3D Prints Build (25 Viewers)
- Thread starter BenCC
- Start date
-
- Tags
- build build thread
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.
BenCC
Supporting Vendor
- Thread starter
- #1,442
That was my concern too. My original cupholder got hot on freeway. I have this prototype on my truck for almost 3 weeks. And I drove the truck from Columbus OH to Chicago, and Great Smokey Mountain. I touched the inside of the holding areas. I didn’t feel the heat. My explanations: the original cupholder are made with injection molding. The wall is very thin, like 2.5 mm. It is basically a shell structure, or more like a stamped part. But 3d printed part, if you go back to look at the pictures, has very thick walls. This may contribute to better thermal insulation.
I am still working on this cupholder. I won’t release it until the I-like-it moment.
I think you can find something better than Fatmat, which is bad by any measure unless it never gets hot where you are. I'm sure there are much better thermal breaks that aren't asphalt based. I might insulate mine with something when it becomes available. Thanx for pointing that out.
gregnash
Anal Retentive Analyst
From what I can tell the few freeway trips I have taken that were more than 30 mins have not yielded the feeling of heat that I noticed. I will keep an eye out the next time I take a longer trip.
Ben did an amazing job with the control unit from an Icom 2730a. I sent him just the detachable head from the radio and he sent it back in a week with the custom mount. All ports, buttons, and controls are accessible. The unit sits high enough and doesn't block the view in the rear view mirror. I fished the control cable through the headliner and down the passenger side A pillar. Main radio unit is mounted under the passenger seat where the stock radio amp used to be.
That bezel's color match to ivory is mint, hit it with some 1200 grit and youre done. Looks great
gregnash
Anal Retentive Analyst
Now that is nifty!!! I like the idea of a small pocket in the side pocket for stuff. Normally if I am on a long trip I take my wallet out and put in the side pocket along with glasses case (in Alita it goes in the top part of center console). It would be nice to have something that doesn't allow the wallet to slide around and whatnot.
On a different note, been doing my normal commute and everything with the cupholders and absolutely LOVE it. Only thing I don't like about it, and is really circumstantial for me, is the wallet/phone slot. I really don't have a need for it so it is just wasted space for me. Taking that out would allow for passenger cup holder to expand to same size as drivers I am assuming @BenCC?
On a different note, been doing my normal commute and everything with the cupholders and absolutely LOVE it. Only thing I don't like about it, and is really circumstantial for me, is the wallet/phone slot. I really don't have a need for it so it is just wasted space for me. Taking that out would allow for passenger cup holder to expand to same size as drivers I am assuming @BenCC?
On the other hand, I'd about kill for that slot. So don't take it out completely, BenCC!!!!
gregnash
Anal Retentive Analyst
I am pretty sure he had planned to have a couple different versions, with and without the slot I believe.
I agree. I like the bright color as well. The pic of the black one shows how hard it is to see stuff in there. Are you going to consider making various colors?
psssst... make it black.
I like the O.E. look of the black. If I can't find something in a 2" deep tray the size of kid's shoebox lid... I've got too much crap in there
I like the O.E. look of the black. If I can't find something in a 2" deep tray the size of kid's shoebox lid... I've got too much crap in there
gregnash
Anal Retentive Analyst
Hell even a light grey color would work in this regard. Just something to create some color contrast is all that is needed really. Did this on my glovebox insert for my 60 from Joey (@NLXTACY ) and when I painted it I went with a light colored gray just a shade or two lighter than the grey interior and it created a nice contrast.
gregnash
Anal Retentive Analyst
Still using the prototype and really haven't come up with any complaints/issues other than what has already been sent over to Ben privately. It gets used daily as this is my DD and I have coffee mugs, blender mugs, etc. that it does great with. The butterfly mechanism definitely comes in handy and the ability to move the butterfly one way or the other is awesome.
Some people like the wallet/phone slot but for me it doesn't do much good. But personal preference there and I know Ben has said he would make a couple versions.
