Hey y'all,
curious what the recommended torque is for this EGR to intake gasket (see photo). I haven't been able to get this fella to seal properly and after two tries I'm clearly doing something wrong.
What's the torque spec and How many foot pounds at a time in sequence? What's the final...
Hello All, I’m getting ready to marry my new transmission to my new engine and need the following torque specs. If someone could provide them or point me in a direction where they can be found, I’d be thankful. Engine is a 2F and transmission is an h55
Flywheel to crank bolt torque
Bell...
Hello everyone,
I have been on the look out for a torque converter for my 1991 80 series. I have a transmission to install but was a new or rebuilt torque converter. Dose anyone know where I can source one?
Hi, While checking the torque for mounting the steering gear to the frame in my rig I realized that there are different torques in Haynes (122 Nm) and RM184E (142 Nm).
Do you know why, and which of these two is correct? The RM184E is from Jan 1980 but in the supplement from 1992 (RM315E) there...
Hey guys,
Did the tri mil header install on my 85 fj60, think the machining was definitely worth it so far as it’s all lined up evenly after some shimming and massaging Looks like everything is pretty level, but I’m wondering if it’s torqued enough. I went to 21 ft pounds (within the range...
Hey all,
Does anyone know what the torque spec is for the exhaust manifold studs for the 1KZ-TE?
I just replaced the studs and the Max Ellery manual only lists the torque specs for the nuts, which is 38 ft Lbs.
So far I have only torqued the studs down to 10 Ft Lbs because I’m afraid to go...
Team,
I am in process of rebuilding my 5/77 2F transfer case rear output seal and e-brake components. I do not have a FSM handy, was hoping you can help here (see pic).
Also, here are the callouts:
1. Rear u joint bolts (4) torque spec
2. Output shaft stake nut (1) torque spec
3. Front u...
If you happen to know: FJ60 rear axle BRAKE BACKING PLATE semi float axle.
Right in the middle of installing a new brake backing plate & will look it up if necessary BUT if you happen to know it would be great, trying to wrap this up today. And a big thanks to @cruisermatt for getting it in...
I’m pulling the trans and tcase as a unit from my 96 landcruiser. 1FZ and A343, usual spec. All the bolts are out, all connectors disconnected, followed the FSM directions. The trans absolutely refuses to separate from the motor. Pulling it from the crossmember mount to the frame with a come...
Hi guys!
I'm just wondering what RPM are you getting when at highway speed like 120 kmh? My 73 with 285/75 tires is almost at 3K RPM. From there it feels like the engine likes to be on that range. I can pull and keep up with traffic easily and its happy to go 140 kmh/3300 rpm.
When I got...
I bought a pre lifted fj60, it's on 33s and there seems to be plenty of room, so a 2" or 3" lift.
The PO has proven to make some odd decisions, so it may have not been aligned/shimmed after the lift.
When on a bump or rutted road, have to work pretty hard to keep it going straight and on the...
Trying to reinstall everything from the transfer case to the front wheels. I've had virtually no success finding torque specs for the GX470 specifically.
I'm convinced I'm looking in the wrong places because I cannot find this information anywhere and I cannot be the only person to ever ask...
If the answer to this question is out there, I haven’t found it, so hopefully this isn’t a redundant post.
Short version
Will a 100 lbs motorcycle carrier, carrying a 400 lbs motorcycle (total weight 500 lbs), which is fully suspended by the standard 2”
hitch of an FZJ80 (itself with a 5000 lbs...
When I'm in high range, my 80 is struggling to go up a mildly steep hill offroad from a stop. Similarly, it struggles to roll over a railroad tie from a complete stop in high and will do the same thing in reverse.
It feels like it's loading up and just can't get enough power/torque to get up...
Recently had new tires installed at the dealer. Asked the dealer to put all 4 to 42psi. After leaving dealer I check pressures with on board monitor 37,44,39,41. So wait until next morning and set the pressures correctly. I always check my lug nut torques after service. 2 foot 1/2" breaker...