Search results for query: *

  • Users: mohawk
  • Content: Threads
  • Order by date

Forum search Google search

  1. mohawk

    Power window switch

    Hi My PZJ 70 power windows have taken a dump ... passenger side will go down but not up with passenger side switch... driver side master switch wont make it go up or down .... the motor is good , i tested that by swapping the wires at the switch ........ i can find heaps of switches for both...
  2. mohawk

    bj75 hauler

  3. mohawk

    Latest bj75 crane mods

  4. mohawk

    new paint

    Giving the pzj some love , but not too much .
  5. mohawk

    Windscreen molding

    Does anyone know where i can buy the windscreen locking strips from ?
  6. mohawk

    75 rear leaf removal

    Hi I want too remove a rear leaf too soften the ride a little and get the rear shackle pointing back instead of forward... i dont mind loosing an inch in height but i cant decide weather too pull the third one down or 4th one down ??? they were new heavy duty springs the PO said but i have no...
  7. mohawk

    H series box

    Can some one tell me simply if the H55f is the same size inside as the H150 / 151 or anywhere near as strong ? Or is it somewhere in between the r151 and h150 strength wise ? Every thread i find seems too end up in a huge amount of confusion and wander off track
  8. mohawk

    3bll power figures

    Where can I find factory power and tourque figures for a 3bll ? Thanks in advance SP
  9. mohawk

    H55f swap

    Ive got a 60 series 5 speed witb manual h4 lever and want too convert too vaccume shift ...do i need too go inside the box or can i bolt my vaccume stuff strait on if i ever need it ? I also need too change the input shaft from h too b series too
  10. mohawk

    Brakes

    The brakes on my 75 are rubbish compared too my 70...i know with 33s and the extra weight they will never be as good but im sure i can doo better...are these a good pad too start with ??...ive had them in stock for three years and i think they are the same as the 70 has now.
  11. mohawk

    Marry xmas from NZ

    Best wishes...its been a good year
  12. mohawk

    Wiper linkage DIY

    When your wipers slow down check for slop in the pivot... I used a 6.5 mm mauser case as a bush too repair my little pzj70 years ago and its still mint..... the 75 was a different bore and had plastic bushes ..they were toast and it was wearing away the casting. 6.5 and 357mag were abit thin but...
  13. mohawk

    Oil pressure sender

    I used the 3bll sender on my 15b when i did the swap , but must have knocked it around abit .. It was working fine but the housing was seeping oil so I bought a new one. It should be correct , part number 83520-60010 and looks the same but the guage is dead... I used thread tape , but earthing...
  14. mohawk

    Daihatsu F50 (skat , TAFT , Wild cat )

    Ive found a mint original low milage one... Its cute as hell 1 owner , 2.5 diesel 4spd and only 60,000 km . Here in New Zealand you dont see many though and if i buy it will be a driver for my missus so knowing what bits are common with other vehicals and any inherant problems would be...
  15. mohawk

    15b power steering pumps

    are 14b and 15bf pumps the same ? theres plenty of 14s on ebay but not so many 15s
  16. mohawk

    2 inch lift

    Im fitting terrain tamer front leaves too my 75,,, with winch and bar how much should it measure from centre of the hub too under side of guard when its done and how much will it drop once its done a few km ?
  17. mohawk

    Exhaust manifold

    I had a set of headers fitted too my 1pz 6 years ago and the gasket has putted out.....Any tricks too avoid snapping studs and wrecking stuff before i rip into it ? should i get the engine hot first ? Should i heat the nuts before trying too undo them ? It has studs and what looks like locking...
  18. mohawk

    heater relay

    my circuit breaker relay keeps tripping out.....is that a stuffed fan motor most likely ?
  19. mohawk

    winch bar mounting

    Ive made a new front bar , but realy only have the 2 12mm bolts at the end of each chassis rail too attatch it too.... The smaller bolts on the side of each rail are either stripped or i cant get a bolt in with the winch mounted... would the 2 12mm bolts be enough if i use grade 8 or 10 bolts ...
  20. mohawk

    My boat

    3mtr aluminium , 10mm bottom (centre ) , 2002 suzuki M18a , 156mm pump , ....Goes hard nuts , good for just under 50mph
Back
Top Bottom