TWT -- The Wrenching Thread (11 Viewers)
- Thread starter jfz80
- Start date
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.
I have several right now. They end up in the scrap yard. I will put the aside. @roadstr6 if you want a small i can get you a inducer fan assembly. Those are the ones that take the combustion air out of the heat exchanger. I dont have anything like what rise has. Everything will be straight drive.
I'm a "fan" of the direct drive units just because they are more compact, can be mounted most anywhere, and less chance stuff (fingers) getting caught up in the pulley. Even the small ones (1/4 HP) move ridiculous amounts of air.
If someone from the triad area makes a run to @Roxx let me know. I could use another 110 if he has enough. Additionally, I'm more than happy to help with wiring and such for those in the area.
If someone from the triad area makes a run to @Roxx let me know. I could use another 110 if he has enough. Additionally, I'm more than happy to help with wiring and such for those in the area.
weekend wrap up with just a couple pics. The pics do not reflect the amount of work that went into it but needless to say, I am worn out.
Saturday I got the CB wired in and mounted. I wanted it to go in the dash but it was going to take more effort than I had time for "this" weekend so a side mount by the shifter will have to do. Started the ARB compressor mounting before I quit Saturday and finished it up Sunday. I decided not to get Landtanks Canister relocation bracket because why would I need to buy a $117 bracket. Looking back I wish I had. I am by no means a fabricator and would like to have done a few things differently but I can touch them up later. Install is complete and the truck is getting ready for Hurricane creek.
Saturday I got the CB wired in and mounted. I wanted it to go in the dash but it was going to take more effort than I had time for "this" weekend so a side mount by the shifter will have to do. Started the ARB compressor mounting before I quit Saturday and finished it up Sunday. I decided not to get Landtanks Canister relocation bracket because why would I need to buy a $117 bracket. Looking back I wish I had. I am by no means a fabricator and would like to have done a few things differently but I can touch them up later. Install is complete and the truck is getting ready for Hurricane creek.
NCFJ
Supporting Vendor
Power and ground buses for interior needs current and future of the 62. Space on the bottom for relays etc. Mounted in drivers kick panel.
Mounted
Mounted
NCFJ
Supporting Vendor
I save some i will inventory the mess and get them aside. I get them a lot so i hope the supply never ends.
Got all the decking finished up on the F550 bed yesterday in the rain. So much rain this time of year.
Need to seal it and mount the fill necks before they fall down onto the road again
Need to seal it and mount the fill necks before they fall down onto the road again
mind sharing the link for where you found that one?Power and ground buses for interior needs current and future of the 62. Space on the bottom for relays etc. Mounted in drivers kick panel.
Mounted
NCFJ
Supporting Vendor
I made it 
Blue Sea components
Blue Sea components
Need to seal it and mount the fill necks before they fall down onto the road again
I must have jinxed myself or something, because yesterday AM I drove to work and the zip tie on the rear fill neck failed. After dragging on the ground for what must have been at least a mile, I backed over the stupid thing getting into a spot
Sometimes you just have to laugh at yourself.
NCFJ
Supporting Vendor
LOL with you Johnny. I did the same with a Hella driving light, had it off the front bumper, hanging, had to move the truck and drove right over it. It falls into the category "What is the cost of stupid today?" Every so often a person just has to pay for stupid
Wrenched on the Jetta again this weekend.
Nothing major. Did rear wheel bearings and rear rotors and pads. Not too bad except for a frozen caliper that took a while to partially rebuild (will have to replace that one soon).
Had front pads and rotors but the fronts were good enough I left them alone for the time being. Most likely i'll do the front bearings at the same time.
Cleaned all the abs speed sensors in an attempt to get that and the traction control working right but it appears one of them is bad. Had to order a VAG COM reader so I can figure out which one it is.
Will put up pics when Andrea sends them to me.
Nothing major. Did rear wheel bearings and rear rotors and pads. Not too bad except for a frozen caliper that took a while to partially rebuild (will have to replace that one soon).
Had front pads and rotors but the fronts were good enough I left them alone for the time being. Most likely i'll do the front bearings at the same time.
Cleaned all the abs speed sensors in an attempt to get that and the traction control working right but it appears one of them is bad. Had to order a VAG COM reader so I can figure out which one it is.
Will put up pics when Andrea sends them to me.
