Builds 'Ele'Ele Build (1 Viewer)

[TRAIL TAILOR]

@TRAIL TAILOR ... You should consider doing this for a living. You're pretty good at this.

I've thought about it.... Just don't want to work that hard.

J

 

[kelly saad]

Tailgate lid is on

Removed the roof rack off and new base mounts are set for the new rack.

Truck Lite military heated headlights arrived too.

Jason

View attachment 1969328
View attachment 1969329

View attachment 1969331

View attachment 1969333

I want this tailgate lid for multiple firearm storage I had a plan to build my own but it would never compare to yours.

 

[yotasavg]

I want this tailgate lid for multiple firearm storage I had a plan to build my own but it would never compare to yours.

SAME x1000000

 

[TRAIL TAILOR]

Side rails are designed for the aluminum rack.

J

 

[civil offroad]

Jason,

Will your new roof rack have a basket, platform, or crossbars?

Vince

 

[TRAIL TAILOR]

Jason,

Will your new roof rack have a basket, platform, or crossbars?

Vince

Vince,

Crossbars only. I'll be putting my hardtop up there.

Jason

 

[TRAIL TAILOR]

Got the 1/4" aluminum side plates cut yesterday and all the crossbar tube arrived. Should be finished and head to powder next week.

Also, made myself a new set of UCAs.. that are a bit more presentable than the " prototype " bare metal and rusty arms. Yes, I always go for the weird color combos.

Next weekend will be a busy one:

• Custom made CrMo CVs, seal, clips, etc...
• UCAs
• Heater Ts
• Valve cover gaskets
• new TruckLite head light swap (7")
• Fit roof rack and hardtop tent
• Trail Tailor 270 batwing and Trail Tailor 2M awnings

Hopefully it all gets done!

J

 

[Beams37]

Got the 1/4" aluminum side plates cut yesterday and all the crossbar tube arrived. Should be finished and head to powder next week.

Also, made myself a new set of UCAs.. that are a bit more presentable than the " prototype " bare metal and rusty arms. Yes, I always go for the weird color combos.

Next weekend will be a busy one:

• Custom made CrMo CVs, seal, clips, etc...
• UCAs
• Heater Ts
• Valve cover gaskets
• new TruckLite head light swap (7")
• Fit roof rack and hardtop tent
• Trail Tailor 270 batwing and Trail Tailor 2M awnings

Hopefully it all gets done!

J

View attachment 1980653View attachment 1980654View attachment 1980657
View attachment 1980658

Are you producing "house-brand" tents an awnings?

 

[TRAIL TAILOR]

Are you producing "house-brand" tents an awnings?

I've had them for a couple years now. I did a group buy for the past two years. I have the tents made to my specs. This hard was a "trial" tent from my MFG and been sitting on the rack for about 2 years. All together I have about 93 tents and around 400 awnings out there.

I still have a couple of tents and 2M awnings remaining.

J

 

[Beams37]

I've had them for a couple years now. I did a group buy for the past two years. I have the tents made to my specs. This hard was a "trial" tent from my MFG and been sitting on the rack for about 2 years. All together I have about 93 tents and around 400 awnings out there.

I still have a couple of tents and 2M awnings remaining.

J

View attachment 1981313
View attachment 1981314

View attachment 1981315View attachment 1981317
View attachment 1981320

Very cool. Would be interested in a hard shell. For me, it just seems simpler.

 

[TRAIL TAILOR]

A few things off the to do list. Will finish the rest tomorrow...

UCAs
CrMo CV axles
Checked all new BL mounts for tightness. No issues
Swapped out the AC control panel in the dash... WOOHOO! all lights work and the mixer now works!
Traced down a short in the radio/video system... Repaired and no more trickle drain on the battery
Removed rear bumper, spare tire lift/carrier and re-routed some wiring so the rear bumper can get started.

NEW PRODUCT---- CB/ANTENNA Mount in stock location (I make this for the 60 and 80 series) Designed prototype mount, ran wiring and installed antenna. Will get to the AM/FM/ CB splitter and CB install in a bit.

Tomorrow---

Heater Ts
Valve cover gaskets and spark plug seals
Plugs
Remove rear crossmember

 

[abuck99]

J-

Did you end up with 4.88's after the 295's went on?

 

[TRAIL TAILOR]

J-

Did you end up with 4.88's after the 295's went on?

A, NOPE... still running the stock 4.30s and getting 13.4 mpg so I'm happy.

J

 

[TRAIL TAILOR]

This morning was good!

All these are off the list.

Heater Ts
Valve cover gaskets and spark plug seals
Plugs
Remove rear crossmember

Also got another Odyssey Extreme 31-PC2150 and installed. 1150 CCA and 205Ah Put it on the charger to test and top off the charge. Nice to have a monster like this again.

J

 

[trdcorolla]

I think you meant 205RC

 

[abuck99]

A, NOPE... still running the stock 4.30s and getting 13.4 mpg so I'm happy.

J

Thanks

My next set of rubber will be 295/70-18- I may require your 12mm pucks after- we’ll see if theres any rub

 

[TRAIL TAILOR]

Rear frame/recovery bracket for the bumper. 1/2" grade 70.

J

 

[MongooseGA]

Jason, I may have missed something in all of the posts.. Are you going to be producing those CVs?

 

[Scrambled]

Rear frame/recovery bracket for the bumper. 1/2" grade 70.

J

View attachment 1988805

Beefy! Any updates to that front bumper?

 

[TRAIL TAILOR]

Jason, I may have missed something in all of the posts.. Are you going to be producing those CVs?

G,

I'm not going to... Even with making 25 sets at a time they would be around 1500.00-1700.00 a pair. The majority of people had a heart attack with that pricing... so another idea hits FILE 13.

J