Builds Benjamin’s 3D Prints Build (11 Viewers)

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Probably a long shot, but if anyone has installed the M2V2 dash mount in their 98-02 Land Cruiser and wants to sell their original dash blank I would very much like to buy it! I have an LX and I want to drill a hole through this blank but I don't want to drill through the wood one. Would much prefer the black plastic in the Land Cruiser and I don's really have a need for the super strong mount that Ben sells (even though it is awesome). Just trying to keep my iPhone mini from sliding around.
 
I can check this weekend for you; if I still have it (which I should), it's yours.
 
Exiled said:
I can check this weekend for you; if I still have it (which I should), it's yours.
Click to expand...
That would be awesome! Thanks!
 
MechE30 said:
I too think that would be a cool product, to replace that panel with a space for switches and maybe a few USB outlets. No need for a cigarette lighter in my opinion.
Click to expand...
Ben is this something you could do? Would be cool to have a few USB outlets and 3-4 rocker switch panels. I bet this would be a very popular product.
 
BenCC said:
Make 5: Scangauge II and Rock Switches Combo Mount for Toyota Land Cruiser 100 Series

5.1 Overview of the Final Product

View attachment 2330078

View attachment 2164397

View attachment 2164396

5.2 Introduction

The combo mount is modeled based on members' requests. Two pockets for rocker switches are added. The rocker switches are fully recessed to protect it from accidental activation.

5.3 Design and Fabrication

The rocker switches are tilted by 15 degrees for better visibility of the stickers. Space is added behind the blades for wire connections.

View attachment 2128854

5.4 Purchase List to Complete the Installation

To complete the installation, the following items will be needed.

Ethernet Cable Extender Adapter

Ethernet Extension Cable (Up Angle)

For a smooth finish, you will need:

3M Bondo 801 Professional Glazing and Spot Putty, 3.0 oz.
Note: Dry sand only. The printing material will warp if exposed to excessive water.

Paint

5.5 Purchase Link

$75 + Shipping (USPS Priority). PM for Direct Paypal Payment.

Can print in Grey, Tan, or Black.
Click to expand...
Looking for the purchase link on this guy please.
 
Mikeybro said:
Looking for the purchase link on this guy please.
Click to expand...
You actually send him an email with your request. Link in the signature
 
Ben, are you using some kind of 3d scanner to get the surrounding geometry for your prints? I tried searching the thread but I may have missed it if you answered before.

The reason I ask is if you do have a scanner, I'd request some scans of the front end. I want to design a hidden winch mount I don't like what's currently out there as you generally have to remove the crash bar and they mount quite low.

Below is my initial design. Not sure if I want to go aluminum or steel, the weld shop at work can do either. Probably aluminum to save a bit of weight.

1718062062449.png

1718062104708.png
 
shtbrwn86 said:
Probably a long shot, but if anyone has installed the M2V2 dash mount in their 98-02 Land Cruiser and wants to sell their original dash blank I would very much like to buy it! I have an LX and I want to drill a hole through this blank but I don't want to drill through the wood one. Would much prefer the black plastic in the Land Cruiser and I don's really have a need for the super strong mount that Ben sells (even though it is awesome). Just trying to keep my iPhone mini from sliding around.
Click to expand...

I just bought the m2v2 but have not installed. You can have my insert when I do it.
 
BenCC said:
Make 5: Scangauge II and Rock Switches Combo Mount for Toyota Land Cruiser 100 Series

5.1 Overview of the Final Product

View attachment 2330078

View attachment 2164397

View attachment 2164396

5.2 Introduction

The combo mount is modeled based on members' requests. Two pockets for rocker switches are added. The rocker switches are fully recessed to protect it from accidental activation.

5.3 Design and Fabrication

The rocker switches are tilted by 15 degrees for better visibility of the stickers. Space is added behind the blades for wire connections.

View attachment 2128854

5.4 Purchase List to Complete the Installation

To complete the installation, the following items will be needed.

Ethernet Cable Extender Adapter

Ethernet Extension Cable (Up Angle)

For a smooth finish, you will need:

3M Bondo 801 Professional Glazing and Spot Putty, 3.0 oz.
Note: Dry sand only. The printing material will warp if exposed to excessive water.

Paint

5.5 Purchase Link

$75 + Shipping (USPS Priority). PM for Direct Paypal Payment.

Can print in Grey, Tan, or Black.
Click to expand...

Was there something like this created to hold the scangauge but instead of the rocker switches there's a spot for a microphone? And a feature of a downward facing type of hole for an ambient light? In my old M5 they had these dim red ambient lights that just gave a little bit of light inside that were quite nice.
 
IS there an aftermarket tray to replace the drop in tray on a 2004 LC - the tray next to the CD/DVD player. Someone broke into my car and took the OEM tray with all my change in it.
 
You must log in or register to reply here.

Similar threads

anthonydiaz85
Alexus - A 2000 LX470 build thread
Replies
17
Views
2K
anthonydiaz85
anthonydiaz85
offoradjunkie
Junkie 100 Build
Replies
0
Views
502
offoradjunkie
offoradjunkie
MobiusR
Project Miramar - LX470 Build
Replies
8
Views
949
MobiusR
MobiusR
S
Sacedog's Build Thread
2 3
Replies
47
Views
5K
Sacedog
S

Users who are viewing this thread

Total: 12 (members: 0, guests: 12)

Share this page

Back
Top Bottom