1968 fj40 resto

[JADCRUISER]

I just put the frame under the top and if I leave 1/4" inch out , it turn like that!!

That looks wrong... Is that your trim in the pic?

 

[brian243]

I think those parts are for where the metal part of the fiberglass cap attaches to the top of the windshield frame.

 

[JADCRUISER]

I think you have rigth,
and the plastic washer are betwen them!!
thanks

I think those parts are for where the metal part of the fiberglass cap attaches to the top of the windshield frame.

 

[JADCRUISER]

car of the wedding!!
My wedding !!
6 years ago from march 25th.................................

 

[KY Longhunter]

Very cool

 

[jvincig01]

I think you asked me for a picture of this.. I have a 67 fj40. I have also taken a picture if my ugly horn button for you. Please please restore this for me, i will pay you! Hahha Let me know if you need me to take any others..

 

[JADCRUISER]

well I send the wiper cover motor for the next generation, the one with one motor , cushions cover and grease cover, you can give some one friend else!!
for the horn button I working on them ,
your looks no crank in it ??

I think you asked me for a picture of this.. I have a 67 fj40. I have also taken a picture if my ugly horn button for you. Please please restore this for me, i will pay you! Hahha Let me know if you need me to take any others..

 

[JADCRUISER]

found the hump, the map lamp and shroud!!!!
almoust complete!!!

 

[JohnnyC]

Map light =interior light = Darth Vader helmet

 

[JADCRUISER]

Im your father........NOOOOOOOOOOOOOOOOOOOOOOOOOOOHHHHHHHHHHHHHHHH!!!!!

Best scream in all movie history

Map light =interior light = Darth Vader helmet

 

[thecrazygreek]

Can you reproduce that hat / cover on your 3d printer?

 

[JADCRUISER]

Im going to try!!

Can you reproduce that hat / cover on your 3d printer?

 

[Tireguy87]

this is what you mean, and the trim that you did went to the rear part to??

Yes mine looked that way too. There are 2 pieces on the side (I think they were the last 2 before the rear corners) that have flat joints. I trimmed about 1/4-1/2 inch off both sides until I had a snug fit

 

[JADCRUISER]

Now Im working on the engine
disassembling the timing cover , I sand blasts and change te cover seal , but when I was preparing the surface to put the gasket, I found this on the cam gear!!
do I need to change it or is usual to go like this ?
please some advice!!!

 

[JADCRUISER]

the gear is on the way from toyota.......
and I start to dissarm the body ...... yesss!!!
that guy is Rene , he help me las nigth until 11:00 pm

 

[JADCRUISER]

SAND BLAST, SOME COSMETIC BONDO AND!!!Almoust to put the radiator decal!!

 

[JADCRUISER]

I canot wait to put the decal!!!
and get the radiator in a box to wait until is going to be reinstaled!!

thanks Shane decals !!!

 

[JADCRUISER]

radiator decal with serial number!!!!
so FUN!!

 

[Pierps]

Your enthusiasm really comes through, man!

This thread is inspiring!! Keep it up!

 

[JADCRUISER]

thanks Pierps
today I got the parts from toyota
Here in Mexico, thay came from california and it was
13523-60030 camshaft gear.............. $170.00
13521-60010 crankshaft timing gear....$ 55.00
I think so good!!
NOW WHATS NEXT??????
can I change the camshaft gear and timing gear without disarm the engine?????
please some advice!!!