24 volts

Hi All, I have a 6lpa 315 that I got used coast guard. Had a blown head gasket that we changed. No leaks now, idles and starts fine but will not rev past 1200 unless primer bulb is pumped while running. If bulb is pumped while running it will hit the limiter. Testing on garage...

@DirtSniffer and I have been talking a lot about different options for the OM606 engine. Power goals, transmission options, transmission controllers, etc. After looking how long our conversations have gotten we figured we should start a thread on this motor since I am sure we aren't the only...

Hello all, Sorry if this is posted in the wrong section. Its my first time asking a question on mud. I have a ‘91 HDJ81 which has recent developed its first leak from a part I cant seem to identify and anyones help would be greatly appreciated. I circled the part on a few different pictures...

Are there any options for the HDJ80 / 1HDT to mount an ARB compressor?

How important is it for this pin to be in the hole? Can i just angle grind it off? Im clocking the turbo

Friends, I have a poverty pack 80-series with the 1HZ engine. 280000 km since 1991. Since it has exactly zero accessories the main thing I miss is A/C in the summers. Otherwise it’s perfect. Does someone know someone that have a thread or have experience in mounting it afterwards? Is...

My 1985 HJ75 Ute didn’t come with a fuel return line. I installed a 12HT and it has a return line. Right now I have it T into the fuel feed line to the pump. I know gassers and HZ and later engines all have fuel return lines, guessing the HJ61 did too but don’t know. I sources the two fuel tank...

I have a 1985 bj60 wit 3b that will not start. I at first poured diesel in the tank and noticed it came right out on the ground. I then ran a hose from the injector pump to a jerry can bled the fuel and proceeded to turn it over hoping it would start. It only turned over though I tried many...

91 HDJ-80. Factory dual battery set up. 24v to start, then 12v to run, including electrical items. Installed 2 AGMs. On the starting battery, LEFT side when facing truck I have an AGM that has marine terminals along with the standard posts. I have the engine's positive and negative cables on the...

I have a question concerning a turn signal issue on my 24V - 1983 BJ40. The left rear turn signal does not work. The left side dash turn signal indicator works….although it flashes very fast, unlike the right side turn indicator which flashes normally. The 24V bulb is fine. I tried a new 24V...

So I haven't been messing with the truck and have just been driving it for the past couple weeks. It's a 1986 4runner with the early 2lt. Subaru TD04L, 2.5" straight pipe. Turbo spools fine, just cruising it sits at 1.5psi. If I get into it, it'll push 15 no problem. It's just so slow though...

Hello, Beware I am not an expert on diesel systems or injector pumps and I have no clue what I’m doing half the time, so any advice no matter how simple you think it is could possibly be of help!! Symptoms: running 1HZ under load, losing power, engine stalls, hard to start and sputters when...

81 BJ42 with 3B (24 V) In process of finishing engine install of the original 3b from the 13B that blew a hole through the piston. Had the 3B running and after I pulled the instrument cluster without disconnecting the battery ground, now I have no power when I turn the the key. No power to...

Greetings! I have just completed replacing my turbo charger on an HD J 81, 1991. My original Turbo charger stopped working around 340,000 km. The only reason that I have so far is that the oil inlet hose was smaller than the Toyota spec hose. Nevertheless, I found a guy in Holland with a firm...

Hello to all you guys ! a lot of time away from this wonderful forum ...but you Know life is strange ... tu cut a long story short : 4 years ago, after 10 years i left my "old" girlfriend so i had to move to new house... at the same time i have changed job company...a lot of new things to...

I've got a ton of blue smoke when I start my 75' Hj45. Stalls out and I start it again...takes a while for it to settle down and smooth out...runs fine after about 10-15 minutes. Injectors? Fuel pump? Any suggestions on where to begin?

Good morning all, I am hoping to track down someone with a 1HD-FT powered HDJ81 in an emissions compliance area of Colorado (front range). I went for inspection at the emissions technical center in Denver this morning and was told that beginning in 1997, the HDJ81 had catalytic converters...

I recently pulled my 13B (with after market turbo from previous owner) from my 81 BJ42 because I heard a concerning noise. Blew a hole in my piston and there were metal pieces on top of my piston. Had a shop assess the injectors and 1 of 4 were operating normally. I decided to install the...

The 14B-T is maybe my favourite B engine and during much internet trawling, I finally came up with some official-looking specs. It comes from a Taiwanese customs website, looks to be an official document for import/registration in Taiwan. The 14B-T was mostly sold in Japan in 24V Dyna/Toyoace...

Got me a running engine for my truck ... but the block is pretty crusty ... just wanted to make sure before going too far on the rebuild that there is no oil gallery on the exhaust side of the block where circled , picture is not mine