What Did You Do with Your 80 This Weekend? (40 Viewers)

[reklund5]

Finally got some time to finish the engine and drop it back in!
View attachment 3750331

Casual post with an F-40 in the background...well done. What turbo are you using on the 1FZ?

 

[ACACG8]

Casual post with an F-40 in the background...well done. What turbo are you using on the 1FZ?

It's the T70 kit from CXracing

 

[nigelsiam]

Finally fixed my rear tailgate handle!! The OME part number is in the photos.

View attachment 3749257

View attachment 3749258

You didn't want to splurge on a new screw?

 

[whiteyota]

Whoa, an F40?
and what is that in front of it?

 

[ACACG8]

Whoa, an F40?
and what is that in front of it?

Its just 2 MR2s

 

[Azca]

Its just 2 MR2s

I'll take one!

 

[Tears]

1997
150000km
Diesel

 

[High Lander]

My only question now is which manual is this shown below? Something used by Toyota US in 1997? Anyone know how I can find one? This was extremely helpful and I think I’d still be tearing my hair out if I hadn’t found this picture.

I have a TVSS IIIB manual if you want it, but it's for RHD cars - DM me

 

[highsierra4x4]

It's the T70 kit from CXracing

Are you running the intercooler that comes with it?

 

[ACACG8]

Are you running the intercooler that comes with it?

no intercooler, I ordered without it, I had planned for a water to air then HG gave up while I had the truck listed for sale

Their 10lbs wastegate is more like 7-8lbs(isnt this what the supercharger runs?), would it be more efficient? yes but, temps are good, and it feels great at 7-8lbs and afr is perfect

 

[lacresta]

Finally got the LP6 mounted up much better than the PO set upView attachment 3748364View attachment 3748365View attachment 3748366

how much difference is there between the LP4 AND LP6 lighting?

 

[lacresta]

Got my rebuilt 1FZ installed!

View attachment 3749302

View attachment 3749303

View attachment 3749304

great color for the valve cover.

 

[Irish Reiver]

Leave your gas off and pull your whip out so its straight. Open the cover up. Try it. Can you hear it "whizzing", like the feed is working correctly? If so, check the spool. With the reel getting lighter, check the pre load on the spool, loosen a little bit and try it again. If that's good, put a little more tension on the feed wheels. Just some things I ran in to in the past with my old Lincoln, not sure what you're using.

Like @cruzinfj1 said above. But also if the wire speed dial/attenuator is dirty, give the contacts a squirt of electronics cleaner and a blow out with compressed air. My welder will sometimes just start spitting wire as fast as it can… I always have to open it up and clean it out with compressed air. Hope you find the fix. Finicky welders can be a pain.

Thanks guys. I tried most of what you suggested already. Ended up calling the supplier yesterday and they agreed it was a fault. Replacement unit arrives tomorrow.

 

[PNWGERMAN]

Finally got round to starting my Coastal Offraod bumper build. Got most of it tacked up before my welder decided it didn't want to play any more

View attachment 3749015

Nice. I built the same one. It was a fun project.

 

[Irish Reiver]

Nice. I built the same one. It was a fun project.

I was surprised how easy it was to put together. I have a 4x4labs to build when the replacement welder arrives.

 

[highsierra4x4]

no intercooler, I ordered without it, I had planned for a water to air then HG gave up while I had the truck listed for sale

Their 10lbs wastegate is more like 7-8lbs(isnt this what the supercharger runs?), would it be more efficient? yes but, temps are good, and it feels great at 7-8lbs and afr is perfecd

Dose there wastegate vent to atmosphere or is it vented internally?

 

[highsierra4x4]

how much difference is there between the LP4 AND LP6 lighting?

I don’t really notice a difference in output. But the lp6 pros have 2 setting a flood and a spot so the flood light dose add when it comes to side output

 

[ofer bruhis]

1997
150000km
Diesel


View attachment 3750364

View attachment 3750365

View attachment 3750366

View attachment 3750367

View attachment 3750368

1HZ?

 

[lacresta]

I don’t really notice a difference in output. But the lp6 pros have 2 setting a flood and a spot so the flood light dose add when it comes to side output

I have the LP6 pro, only have the high beam hooked up with spot driving combo for the lens. I like the size of the LP4 on your bumper.

 

[ACACG8]

Dose there wastegate vent to atmosphere or is it vented internally?

atmosphere, not a fan