I just sent a message to Roxx so I'll see what we work out. I'm also in Richmond, VA so I have to work that out too...
Official ONSC member buying/selling thread (8 Viewers)
- Thread starter southerncruiser62
- Start date
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.
I just sent a message to Roxx so I'll see what we work out. I'm also in Richmond, VA so I have to work that out too...
jfz80
Cruisin’
If you can work it out by relic run and can get it to somone headed back to the triad it can hang out and wait here for you in Madison Nc. Save a few hours driving. Or shipping via fastenal may be the easy choice.
Looking for an 80s series exterior drivers side door handle if anyone has one near the triad... Color isn't super important to me
I have a few, in Siler City.
Now I’m in need off a 80 series front e locker housing. The one on it now is shot
S4Cruiser
SILVER Star
Dang! Bent or what??
sleepycruiser
I will get by….I will survive -Touch of Grey LC200
NCFJ
Supporting Vendor
Ouch!
NCFJ
Supporting Vendor
Well thats ugly
S4Cruiser
SILVER Star
jfz80
Cruisin’
Sooo. What were you really doing? 
Well me and my friend for our spring break trip took a trip out to uwharrie for a couple days and when going up the backside of daniel we got to the top we stopped and ate lunch and went to go back down the backside and when i backed up to do a u-turn the rear end was just sliding down the hill when i would go to back up. Center diff was on and i had the rear locker on, we looked out the windows and to the front and none of the front wheels were spinning. I didn't aggressively go up anything or beat on it, and honestly didn't hear it break or anything. Limped it till i heard a noise and when i did i stopped and pulled started pulling the driveflange off till our phones blew up with tornado warnings about an hour after working on it*plan was to be out of the forest when the time arose*. so i put it together and we limped out of there and took it to @neslrac house and to try and fix it, went to andersons to get a birf and got back to take it apart, outer axle housing looked fine and inside of knuckle was fine when i got it all apart, but when i wiped the inside it just shredded the paper towel, Made some calls to dad and Del (@SFROMAN) and he dropped what he was doing to tow me home, Very thankful for that and getting home safely. Now back to your normal broadcast of selling stuff.
I'd polish it up, and run it. What's the worst that could happen?
You can also replace just that part. I have a housing that you can take that part from. The housing is not looked or lhd that is the reason why i dont offer the housing As a replacement.
Does anyone have any aftermarket crossbars and mounts for a 100 series that would support a roof top tent?
My intention is to order a Bowfin rack, but they are sold out right now. I would like to mount a Frontrunner Rooftop Tent atleast (awning later) until I can get a full rack and was hoping to be able to use it at the Relic Run. Thank you in advance.
My intention is to order a Bowfin rack, but they are sold out right now. I would like to mount a Frontrunner Rooftop Tent atleast (awning later) until I can get a full rack and was hoping to be able to use it at the Relic Run. Thank you in advance.
Anyone have an extra lx470 wheel cap for an 18" 2003+ wheel they would be willing to part with?? The retaining ring on one of mine bit the dust.
Like this:
GENUINE LEXUS 4260360600 LX470 (03-04) WHEEL CENTER CAP 42603-60600 ! | eBay
Like this:
GENUINE LEXUS 4260360600 LX470 (03-04) WHEEL CENTER CAP 42603-60600 ! | eBay
