Builds LHD HZJ73 Refresh

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Got side two done. Added come gussets on the upside. I’m sure the plates are designed to “45” off the bottom of the frame but they would have gotten in the way of the skid plate.

The front support leg needed some custom fab to work around the exhaust. Basically made a 1/4” plate off the frame to get around it.

Off to powder……

View attachment 2723774


Oh I have seen far worse welds my man. 😉

Cheers
 
It’s amazing how busy these engine bays are but I managed to find a great spot for the 24v ARB compressor. I used Rivnuts to attach it to the inner fender

19103EDC-3907-415D-993F-54E9A7D385BB.webp
 
It’s amazing how busy these engine bays are but I managed to find a great spot for the 24v ARB compressor. I used Rivnuts to attach it to the inner fender


Have you looked under the hood of a 13BT powered cruiser? Makes the 1HZ look downright cavernous.
 
Have you looked under the hood of a 13BT powered cruiser? Makes the 1HZ look downright cavernous.

Ive spent exactly the amount of time it has taken me to bleed brakes, add this wiring and wire the winch looking at any Toyota Diesel motor so nope.

Battery 1….Battery 2…..24 volt stuff. Getting it.
 
Ive spent exactly the amount of time it has taken me to bleed brakes, add this wiring and wire the winch looking at any Toyota Diesel motor so nope.

Battery 1….Battery 2…..24 volt stuff. Getting it.

Not all diesels are 24volt, Australia is one of the 12V countries.

The 13BT under hood shot courtesy of Heritage Museum

BJ774V MNX 89 GREY web ready023.webp
 
Nice of them to put both batteries on the same side though
Mhm, kind of. I suppose this is on RHD vehicles only.
In my BJ73 LHD, one battery is left and one is right. With a long connection wire going all the way round the cooler.
I assume 74s LHD are same setup.
 
Got the sliders burned on. These fit this wheelbase very nice. The only major adjustment I had to make was passenger front to get around the exhaust. First pic is my solution. That is between the spring hanger and the crossmember.

51A8391B-546D-429F-A681-9F7512999BE7.webp


253CEDB0-D8F4-4FBC-B96A-CEBEF15688CF.webp


60ADAFCB-5290-4FAC-A68F-12371B384758.webp


63E9CDAA-994A-4CD3-8CEF-1B80BA35E71F.webp


E70D6FD7-08ED-46B0-9DD8-DA09C48F9688.webp
 
I’ve wired the 24v compressor like ARB recommends.

Red + to Battery 2 positive

Black/white to to Battery 2 negative

Solid Black 5 amp to battery 2 negative.

The Powerprobe says I’m only getting voltage from Battery 2 at the 40 amp fuse.

Compressor has been tested with the powerprobe and it works.



A973CA0D-AFB5-4A51-897B-E6E6E1731E78.webp
 
Aight. I figured it out. Thanks @Onur and @SNLC for letting me bounce this off you.

Turns out the ARB diagram to use Battery 2 for positive and Battery 1 as negative is wrong. That only got me 12v

Must have pissed the relay off with all the messing with it as it was bad. I stole one off my FJ55 ARB and it fired up…..

Yeah.
 
Finally got the correct Dobinsons drawers today. GX….

I was going to use turnbuckles but decided I don’t like the look so I’ll work on bolting this all down later in the week when I get back in town

National Luna Dual Zone 55L is pimp too

6BCED750-B5CF-4376-B69D-CEF25E51390F.webp


705C6306-724C-4E4D-8176-D3401C0C1AB2.webp


8738B828-3A6C-458D-946C-D1DDA4BC1382.webp


F0A356B0-4BEB-4E9D-B69E-CC818604DE11.webp


0E8BC1D7-070F-479C-B070-8072DE3E4224.webp
 

Users who are viewing this thread

Back
Top Bottom