transfer

Hi all, i just imported my 1991 70 series from Venezuela, i went and bought it over there and did some kind of restoration, but now that i have it here in the US i found that the transmission has some leaks by the upper plug, looks like was already welded, also on the transfer on the upper...

I have searched but have not identified specific transfer case differences for t-cases behind the LC200 8 speed transmissions, or the LC200 6 speed transmissions, or the LS460 AWD sedan 8 speed transmissions. I am interested to understand whether or not anyone has used an LS460’s 1UR-FSE V8...

Looking for the above 91-94 transfer case shifter base which bolts to the top of the trans. Thanks!

Per title, looks good just a little dirty Asking $65 shipped conus

My '79 FJ 55 which I have owned for going on 40 years has a very noisy transfer case and seems like it's getting noisier lately. I recently drained and refilled the T-case and the 90 w looked a bit like metallic paint. Made me think about the statement 'All that glitters isn't gold'. I have...

This came off my '67. Asking $80 + ride

Problem: Can't get out of 4hi. Removed the center console, lubricated all that I could see, nothing. Remove the linkage from transfer case to shifter, case will go into 4hi and 4lo but the shifter is stuck. That was a big relief knowing that the case itself isn't the problem but I still need...

I have my drive train and block assembled but once the transmission and transfer case are not supported by the transmission jack it rolls and not sure how far it will go. Even when just lifting the gear boxes with the transmission jack I need to use the floor jack under the output side of...

Does this mean the seal between the transmission and transfer case has finally given up? This is after sitting for a couple of weeks. Last night I noticed the fluid about an inch in the tube at the bottom. Now it’s definitely higher.

Hi guys, thank you for understanding for beginner! Until rebuild my transfer case HF1A i have some trouble-missunderstanding about one part. I see this pin on the diagram but can not find in manual, should be instal it or not ? Can sombody explain ? Thank you so much Dave

Do the FZJ80, HDJ80, and HDj81 all share the same transfer case, or do they have differences? Thanks in advance.

Hey everyone, I'm looking to see if anyone here has or knows of someone looking to get rid of an sm420 to LC 3sp adapter plate. I'm striking out pretty hard on locating one because apparently they have fallen out of demand. If anyone has any leads, I'd greatly appreciate it. Thanks Mike D

I have a 1973 FJ40 that Im swapping the original 3 speed for a TH350. While I have the tranfer case out I want to reseal / new gaskets

While trying to figure out a T-case shifter bracket from my 4L80 to T-case I'm now questioning how the H-N-L operates. I see if you do a twin stick you need a different 2h-4h shift rod but wondering why? How does it affect the H-N-L shift lever? I can move the H_N_L lever no matter what...

Let me know if anyone has a used HF2AV transfer case for a 97 80 series in good working condition. I'm in the DFW area and can pick up. Thanks!

I conquered the front DS clearance issue, but have been struggling with getting the TC shifter to function. I have built several types of mounts off of the trans for the factory shifter, but just can't seem to get the H-N-L portion to function appropriately. For those who have tackled this, do...

Looking for an early model transfer case shifter retainer and shaft (PN: 36344-60021), the pic should show exactly what I am looking for, it's needed for the LT swap kit I have from @torfab Any questions please let me know. Thanks.

The vehicle is a 1997 FZJ80 with an HF2F installed as a replacement for the HF2AV. I did this about 10 years ago, I have a vague memory the drive shafts were different lengths. Due to a maintenace brain fault, I neglected to grease the splines (yes !! I neglected to do that. ) and now the shaft...

Offering up the transfer case off of my 100. It is more than likely in need of a rebuild. The front puts out shaft studs are stripped and need replacing. The case leaks at the front output flange as well. Great for someone who wants to re-gear without having much downtime. Can ship at buyers...

Guys, I have a 04 LC FSM and below is what I extracted from it. Doing the diff and transfer case oil service in few days. Hopefully torque specs are good for 06 as well. But let me know. Transfer Case Protector - 3 Bolts - Torque: 28 N·m 75W-90 (Mobile 1 Synthetic) 1.3 Liters - 1.4 US Qts...