transfer

I'm aiming to rebuild my case next spring. 83 FJ60. Currently have a 4spd/stock case/stock diffs rolling 33x10.50r15s. I plan to keep the 2F/4spd until they blow. It runs great now and hopefully with some preventative maintiance we should be in the clear for a while. Future plans will be...

Hey Folks, I'm researching my next build and I'm planning on a 2.8 Durax that is tuned to 220hp / 440tq. With that level of torque, I seem to not be able to find any specs on max torque of land cruise transfer cases. I was think of going with a FJ62 case converted to FJ60 shifters. What do...

Have two 3-speed transmission/transfer cases. One is column shift from a 67, the other is floor shift (converted with what I believe is the OEM top cover) Neither have parking brake drum or backing plate. Both are cores, condition unknown. Asking $200 for each. Can ship anywhere.

Came off a 1970 I parted. Not a complete setup. What you see is what you get $10 plus shipping

We were doing 5 Speed swap on FJ62 and ordered this kit. The idler shaft diameter is smaller. So we ordered a new kit and can't return this one. I took a picture of the kit and number. Please do your research. Make me an offer.

I bought a used transfer case from CruiserParts with plans to do an ultra low range swap. My plans have changed and I am no longer going to go this route. Does not include with sensors or CDL motor. One of the studs on the rear output is spinning which would need to be addressed before...

Suddenly getting a metallic noise from the transfer case shifter. Check out the video below. I can even feel a corresponding vibration on the TC shifter when I hear it. Checked both the TC and transmission oil and I'm good. Thoughts?

Been chasing a loud whine in transfer case along with a fair bit of slop/lash. I just started pulling it apart and it appears that the output gear splines are pretty loose on the shaft. I have heard that the output gears and bearings are not supposed to be tight on the output shaft, but this...

I’m just about to paint the FJ 40 and I have the transmission tunnel off and I noticed that my transmission and transfer case linkages do not match the holes on my cover. Any help would be appreciated

I have an automatic transmission from my 1988 FJ62 with transfer case. Thee transmission got overheated so I swapped it with a replacement. Transfer case is solid. Make offer/any offer. Not willing to ship located in Long Beach Ca.

I have a complete F engine, transmission, transfer case out of a 72 F40 for sale. It ran when removed and has been sitting for a bit. It is complete with all manifolds, carb&air cleaner, valve cover, flywheel & bell housing, water pump & all pulleys, alternator, motor mounts and more. It was...

I have to drop my transfer case to repair a screw up of my own making, but have another engine project I need to do that I could knock out while I'm waiting for parts. Is there any danger/risk to running the engine while the transfer is removed? It wouldn't be moved/driven, just idled in Park.

I recently removed my rear driveshaft to have it rebuilt. While I was under the truck I decided to change the transmission oil. To make the job easier I removed the transcross member (the bar that extends from one frame rail to the other that the skid plate attaches to under the transfer case)...

Picked up a fixer upper 40 that needs a transfer case for my stock 4 speed transmission.

Any one want to guess how many different shift patterns and drive trains there are for the FJ40? Well I’ll tell you it’s ridiculous. I’ll tell you at the very end of this post. I recently learned Advance Adapters makes a transfer case that you can connect an Automatic Transmission to. So after...

Spent the whole afternoon on a new bearing and seal. Cracked the extension housing on reinstall. Either misaligned the pump drive or the pump spacer fell down. Doggone it. Pics of the part that went well:

I'm about to go replace the output seal on my transfer case and trying to mentally walk through the job before tearing into it. Can the rear extension housing be removed with the crossmember still bolted to the frame rails? Planning to replace the output seal, bearing, snap rings, speedo...

Out of an HZJ77, 1992, 150k km on both. It is a part-time transfer case. Asking $900 $500 for both. Must be picked up, will not seperate. Sold together.

Looking for transmission and transfer case for 1994 LC FJ80 - OEM parts numbers above. Thanks.

1985 hj75 troopy, Oz, manual h55f. Not sure if I should post in 60's section as most 70's posts are for newer than what I have. Rebuilding h55f transfer. Have watched both otram and George's videos also referring to toyota manual and amayama schematic. Both Otram's and Georges videos are...