What have you done to your 200 Series this week? (20 Viewers)

[Eggrollz]

ok, need details on this.

18x9.5 +0
275/70
Lots of trimming lol

 

[tbisaacs]

18x9.5 +0
275/70
Lots of trimming lol

View attachment 3248387

 

[LX Cruiser]

I had a bit of time to get a couple things done to the LX yesterday. I replaced the PCV valve. 3 minute job and a $6 part. The original was seized. It's supposed to rattle when shaken, but my old one is totally gunked up. I'm thinking that this is going to fix the milkshake under the oil cap that I have been noticing lately. If not, I might add a catch can, but I think the new PCV valve fixed that issue.

Checked under the oil cap this morning. I think this puts me on team No Catch Can Needed.

 

[CharlieS]

Checked under the oil cap this morning. I think this puts me on team No Catch Can Needed.
View attachment 3248969

Everyone that isn't on a racetrack is in team no catch can needed.

 

[Tex68w]

Yea if you don't have a diesel 200 I wouldn't waste your money on a catch can.

 

[turbo8]

Got these is today. Going to drop them off at anodizer tomorrow. I opened them up for pre order on the site.

35mm recovery point | E&E Off-Road

Low profile rear recovery point designed for the 200 seriesWill fit other vehicles with 35mm bolt spacingUsed with regular or soft shackle.Rated at 10,000 Lbs with a 2X safety factorUsed for vehicle recovery and tying downMade from 7075-T6 aluminum1 recovery point and JIS 10.9 hardware are...

www.ee-offroading.com

I also got these is and about to do a test fit if everything goes well they will be off to the anodizer as well.

 

[AnyMal]

Got these is today. Going to drop them off at anodizer tomorrow. I opened them up for pre order on the site.

35mm recovery point | E&E Off-Road

Low profile rear recovery point designed for the 200 seriesWill fit other vehicles with 35mm bolt spacingUsed with regular or soft shackle.Rated at 10,000 Lbs with a 2X safety factorUsed for vehicle recovery and tying downMade from 7075-T6 aluminum1 recovery point and JIS 10.9 hardware are...

www.ee-offroading.com

View attachment 3249334View attachment 3249343
I also got these is and about to do a test fit if everything goes well they will be off to the anodizer as well.
View attachment 3249346

Will these be black when i get em? I dont mind either way. My UCAs are raw too. I like how the silver bits are just barely visible underneath.

 

[turbo8]

Will these be black when i get em? I dont mind either way. My UCAs are raw too. I like how the silver bits are just barely visible underneath.

You ordered a black set, but I can send you a clear anodized set instead.

 

[AnyMal]

You ordered a black set, but I can send you a clear anodized set instead.

What do y’all think?

Should i match these for poser points?

My westcott was in black though but thats all hidden. These both would be a little hidden easter egg for my otherwise sleeper look.

I think if its not too much trouble for you silver? Forum losers? What say you?

 

[turbo8]

What do y’all think?

Should i match these for poser points?

View attachment 3249825

My westcott was in black though but thats all hidden. These both would be a little hidden easter egg for my otherwise sleeper look.

I think if its not too much trouble for you silver? Forum losers? What say you?

Clear hard anodize will look like the recovery point, the skid is uncoated aluminum.

 

[Tex68w]

My black front tow points have already faded into a sort of grey/silver on the front so might as well get the clear ano. Unfortunate side effect of anodized parts at times, I’ve seen black turn to brown and purple as well.

 

[a200]

What do y’all think?

Should i match these for poser points?

View attachment 3249825

My westcott was in black though but thats all hidden. These both would be a little hidden easter egg for my otherwise sleeper look.

I think if its not too much trouble for you silver? Forum losers? What say you?

I like bright shiny aluminum.

 

[AnyMal]

@turbo8

Silver then!! Thanks and sorry if that messed you up at all.
And i will be buying those skids at some point!

 

[AnyMal]

My black front tow points have already faded into a sort of grey/silver on the front so might as well get the clear ano. Unfortunate side effect of anodized parts at times, I’ve seen black turn to brown and purple as well.

Even the westcott collar and kit had a purple tinge to it. Kind if wish i went raw now.

 

[turbo8]

My black front tow points have already faded into a sort of grey/silver on the front so might as well get the clear ano. Unfortunate side effect of anodized parts at times, I’ve seen black turn to brown and purple as well.

Can you post a picture, anodizer was suppose to use inorganic dye, which should hold up to UV light.

 

[yotantexas]

Seat belt and fuel pump recall. Also Dobinson IMS lift with Goodyear Ultraterrain AT in 275/70/18.



Very pleased with the set up. 

 

[Julian73]

Even the westcott collar and kit had a purple tinge to it. Kind if wish i went raw now.

Poor anodizing. Sailboat masts and hardware used to be trendy in black, the type and thickness lasted years in sun and salt air.

 

[Eggrollz]

Super high quality over priced plastic caps

 

[toofrigginswt]

Worked on the front end this week. Currently deciding where I want to mount the pod lights. I’ll probably end up getting a smaller 2 inch light at the ends.

 

[desmocruiser]

So my 2013 Lexus Was kinda busy for few weeks, painted the roof jet black and half the spoiler, installed F sport grill, installed sport body kit, installed osram 7000k headlights bulbs, led fog lights, led interior lights and side steps, tinted the whole truck 5% all windows 35% windshield. Ordered vline grom system and sealed the carpet with plastic "dealer must remove protective cover" after a interior detail. My next project is to chrome delete and wrap the mirrors with gloss black wrap. View attachment 3225129

View attachment 3225130

View attachment 3225131

View attachment 3225132

View attachment 3225135

The grille and roof look great!

Did you paint or wrap the roof? I wrapped my last build and really liked the look and thought the wrap turned out great and added paint protection, contemplating doing the current.