Found a few - LOVE it
What have you done to your 200 Series this week? (20 Viewers)
- Thread starter MScruiser
- Start date
-
- Tags
- 200 series
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.
Giamviti Dash Mount added this week. I ran (2) 15A cigar plugs (Blue Sea) in ARB Fridge plug holders. Also added Ram Track mount for phones and maybe future Garmin Overlander or something in that lineup/iPad Mini. Ran #10 power/ground to a Blue Sea Fuse block. Wired hot to Aux Group 31.
I like this a lot. What did you paint the gamiviti panel with?
Was going to install a Curt Front Trailer hitch today. I've had these on our farm trucks and they are handy as heck when moving carts that steer
at the front where the hitch is located.
and had a look first.
From the looks of things I may be better off with a rectangle or square hole. A fabricator friend can make a cover. Will use Rivet Nuts to secure it. Stay tuned.
PS: Contacted Curt, fwiw, to let them know. Pretty sure shield is NOT spelled "Sheild"
at the front where the hitch is located.
2" FRONT RECEIVER HITCH, SELECT TOYOTA LAND CRUISER, SEQUOIA, TUNDRA #31198
Unfortunately, the diagram for the cut-out for oil filter access is 100% wrong. Glad I put it on the liftand had a look first.
From the looks of things I may be better off with a rectangle or square hole. A fabricator friend can make a cover. Will use Rivet Nuts to secure it. Stay tuned.
PS: Contacted Curt, fwiw, to let them know. Pretty sure shield is NOT spelled "Sheild"
I used the AEV black textured paint.
turbo8
Supporting Vendor
I launched my site and ready to accept orders on it.
www.ee-offroading.com
I only have limited supplies of the following:
Low profile front recovery points in black and clear hard anodize, which are ready now.
I will have a couple sets of red anodized ones for pre order, which should be ready in a week.
Low profile recovery hitch for soft shackles (as far as I know, this only fits the 200 series)
I have 5 uncoated for sale now, with black\clear hard anodize and red anodize that will be ready in a week.
RLCA brace\skids
I have a few of these in stock
Use promo code LAUNCHSALE23 to get 15% off your order. Sale ends 1/15/23
There are some product reviews from some members that I pulled from here, if you want me to remove them, I will.
Thanks everyone for your support, really appreciate it!
Hopefully this works better than the launch of a certain healthcare site...
www.ee-offroading.com
I only have limited supplies of the following:
Low profile front recovery points in black and clear hard anodize, which are ready now.
I will have a couple sets of red anodized ones for pre order, which should be ready in a week.
Low profile recovery hitch for soft shackles (as far as I know, this only fits the 200 series)
I have 5 uncoated for sale now, with black\clear hard anodize and red anodize that will be ready in a week.
RLCA brace\skids
I have a few of these in stock
Use promo code LAUNCHSALE23 to get 15% off your order. Sale ends 1/15/23
There are some product reviews from some members that I pulled from here, if you want me to remove them, I will.
Thanks everyone for your support, really appreciate it!
Hopefully this works better than the launch of a certain healthcare site...
Last edited:
Interested to see how this comes out.
Love the low profile rear bumper!
my company's IT has blocked your site -- just an FYI so you can work on getting past this
turbo8
Supporting Vendor
My day job company IT blocked it as well, trying to figure out why. Hosting site is through wix.
Looks like you need to get Cisco to think your site is safer. Probably a lot of companies use Umbrella for DNS security.
turbo8
Supporting Vendor
turbo8
Supporting Vendor
It's working on my work network now. It was being blocked as it was a "newly seen domain".
Yep no longer blocked on my end - good luck with the venture
I was going to quote how your rear end is as messed up as mine, and that it would be awesome if a company made rear diff skids for 200s. But i know the hivemind is completely against diff skids "its not needed"
Sand paper and a rattle can, sand paper is optional.
kcjaz
SILVER Star
Are those Bub Built skids? Looks like you can remove them except maybe the gas tank.
Upon further review I think this is going back. I'll have to cut things to make it fit and that's not happening. Have a local fabricator that can do this
in his sleep and it will fit perfectly. Of course it will cost more. This one size fits all it getting old. Heck, I may even just bite the bullet for a front bumper.
in his sleep and it will fit perfectly. Of course it will cost more. This one size fits all it getting old. Heck, I may even just bite the bullet for a front bumper.
That's a real ground clearance killer. Do you want this so you can tow the LC, or is this for mounting attachments?Upon further review I think this is going back. I'll have to cut things to make it fit and that's not happening. Have a local fabricator that can do this
in his sleep and it will fit perfectly. Of course it will cost more. This one size fits all it getting old. Heck, I may even just bite the bullet for a front bumper.
View attachment 3211828
View attachment 3211830
Might talk to Trail Tailor, or one of the other guys who makes a hidden winch mount for the 200 and see if it can be modified to have a 2" receiver on it. You' definitely have to cut up your bumper for the receiver to pass through with that option though.
