What have you done to your 100 Series this week? (34 Viewers)

[Trapper50cal]

added a little customization to the ebay snorkel.

View attachment 3965403

View attachment 3965404

Me likey!
Source?

 

[ODOverland]

Me likey!
Source?

we have printers here at work.. me and another guy have been working on them.. got it now where just about anything can be added.

 

[Kavyp41]

Just had our local shop install a new starter for my LX. When they were working on the car they saw some fluid (coolant) leaking and saw that one of my heather T's were broken. It actually was all looking all good from a quick glance before a trip, but had completely cracked right where it connects so looked good to go. A job that I just kept putting off knowing it needed to be done and even had the parts for. Well luckily nothing catastrophic happened and the LX is back up and starting right away and running top notch. Thank you Higgy's for the help and a BIG reminder to do your Heather T's and double check everything.

 

[elemenohpee]

3d printed a sleeve for my swing arm latch so that it can accept standard bike grips. The longer length of this makes things so much easier and prevents me from slamming my hands into the locking pin.

 

[Norilsk]

Took her for a quick test drive around. So far feels nice, I got 65mm of down travel, need to finish the body work, build gas tank skid plate, sliders, front bumper for the winch and do the timing belt/new radiator.

 

[saucebox]

3d printed a sleeve for my swing arm latch so that it can accept standard bike grips. The longer length of this makes things so much easier and prevents me from slamming my hands into the locking pin.

View attachment 3965962

Put some up for sale!

 

[Ouray19]

Took her for a quick test drive around. So far feels nice, I got 65mm of down travel, need to finish the body work, build gas tank skid plate, sliders, front bumper for the winch and do the timing belt/new radiator.

View attachment 3966038

View attachment 3966039

oooo, I have the same Tundra/Sequoia(?) wheels. Did you pick up the SLEE spacers? Such a nice wheel.

 

[OEMGUY0720]

Thank you for the 19 solid years of service. Went OEM+ and honestly I may have overspent a little bit on the new oil fill cap

 

[Norilsk]

oooo, I have the same Tundra/Sequoia(?) wheels. Did you pick up the SLEE spacers? Such a nice wheel.

I got the front spacers from Bora, they are 1" thick just enough to get the tire away from the upper control arm

 

[jaewastooshort]

Replacing the brown with a little green .

I didn't realize that these panels were available... do you happen to know part numbers? I may have to dig thru the partsouq more because I didn't see the smaller panel numbers when I searched previously. I've been figuring I'd have to shape replacement pieces myself.

 

[Unrulykid]

I didn't realize that these panels were available... do you happen to know part numbers? I may have to dig thru the partsouq more because I didn't see the smaller panel numbers when I searched previously. I've been figuring I'd have to shape replacement pieces myself.

https://partsouq.com/en/catalog/genuine/parts?c=LEXUS00&ssd=%24%2AKwGyhpeTw-zu4tXG0-eLmur-3tnHtrm0taeIu_P1xtHFyc_HlZKCxMTI09PV1M2XkLXf8fXxwMvSzpGD-7DWsbWztLe87uL6_u_G_KL1pL77jemso-WlurP7-qy-r8D6pOTp5aS-6_vp5ujipbqjsrzp5Omso-_poruksOHn_bW2wKX9__DtvZewoujypbqj0M2X9eei6PWluqPM0JOfn7Cx0bCysrO14eD-saOqpePipL774PKytbO3oq2k6br18aLU3M2xsbbI9JCF0MbNxqKtpOKws-m6sPsAAAAAz91r4w%3D%3D%24&vid=0&gid=885&q=JTJHT00W723518751

 

[ZG MN]

3d printed a sleeve for my swing arm latch so that it can accept standard bike grips. The longer length of this makes things so much easier and prevents me from slamming my hands into the locking pin.

This is such a great idea

 

[mokrunka]

Replaced the 2 front door seals. They weren't leaking, but were starting to sag in parts. The new seals are TIGHT, gotta really slam the doors, and totally quiet inside now (I did the rear two a few months back).

Up next for later this weekend is outer tie rod ends.

 

[95Fantasma80]

Front bumper

That's amazing! Did you have to adjust AHC at all? I am thinking of adding to my 2001 LX470.

 

[95Fantasma80]

Updated front end lighting. Installed my LED retrofits from TEQ Customs. Light output is AWESOME!!! Also installed new OEM corner lamp housings and new fog lamp housings along with some Weather Tech lamp guards to protect all the new housings. Really freshened up the front end.

View attachment 3937331

View attachment 3937332

View attachment 3937333

This looks incredible, and looks stock! what option did you choose in the order page, I would like to do the same.