What have you done to your 100 Series this week? (75 Viewers)
- Thread starter SHUSH
- Start date
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.
installed
mdcoa
SILVER Star
New pcv hoses (discovered I had the wrong style PCV valve so that’ll go on next week), new fuel filter, and replaced the MIA brake bleeder valve caps.
Yesterday the dealer balanced and rotated my wheels (told them about ten times to do all five—looks like they did four) and aligned my front end, although it looks suspiciously like they only even attempted to correct toe....so I’ll be going back.
Yesterday the dealer balanced and rotated my wheels (told them about ten times to do all five—looks like they did four) and aligned my front end, although it looks suspiciously like they only even attempted to correct toe....so I’ll be going back.
Thank you for the reminder to get new brake bleeder point caps.
awesome job!
yngmrostrvile
GOLD Star
Fell in love all over again. Finalized the house battery installation. Super stoked about next weeks trip to Chiricahua Mntns.
Nearly finished installing rear view and reversing camera. My beautiful but short bride will be driving the cruiser full time when we sell her car.
First Leather Butter, then a couple soaks with chemical guys leather stuff. It’s nice to feel it change from crunchy to soft
Nice! What awning do you have and is it noisy when driving hwy?? Thx, looks like y’all had fun!
Finally figured this one out. Replaced the tape deck with a single DIN headunit on 2002 with nav.
It looks like the nav functionality still works, cannot confirm since a motor in my nav unit is dead and prevents it from loading the map. Project for another day.
Used a 68 ohm resistor bypass on the connecter in back and used the other terminals in the connector to power the unit. Ran speaker wire down under the passenger seat and connected to the speaker outputs off the connector on the factory amp.
I followed instructions mainly from this thread, post #72.
68 ohm resistor to replace stereo on NAV equipped LC and LX - https://forum.ih8mud.com/threads/68-ohm-resistor-to-replace-stereo-on-nav-equipped-lc-and-lx.965785/
Pretty easy to do technically, just a few hours of connecting wires.
It looks like the nav functionality still works, cannot confirm since a motor in my nav unit is dead and prevents it from loading the map. Project for another day.
Used a 68 ohm resistor bypass on the connecter in back and used the other terminals in the connector to power the unit. Ran speaker wire down under the passenger seat and connected to the speaker outputs off the connector on the factory amp.
I followed instructions mainly from this thread, post #72.
68 ohm resistor to replace stereo on NAV equipped LC and LX - https://forum.ih8mud.com/threads/68-ohm-resistor-to-replace-stereo-on-nav-equipped-lc-and-lx.965785/
Pretty easy to do technically, just a few hours of connecting wires.
First pic is right after I bought her.
BullElk
SILVER Star
What happened to your fuses where you put your fused line? I have fuses in those empty slots in your picture.
Me likey! Any link for the camera and screen you used?
Bought it from elinz but after looking through aliexpress it appears to be available there as well.
Hopefully go for a drive this afternoon and see how it goes. Ran out of time yesterday.
7" Rearview Mirror Monitor 12V 24V Reversing CCD Camera Truck Caravan| Rearview Mirror monitor
7 inches Rearview Mirror Monitor 12V 24V Reversing CCD Camera built to withstand shock and vibration. An excellent rearview monitor with infrared IR Night vision and waterproof camera.
www.elinz.com.au
Like what you did here. Care to elaborate on your setup.
Rear view camera added into existing headunit; added a cellphone claw while I had the dash apart. There’s more room in there for activities than I thought.
Completed the swing arm tire carrier on the Dissent Offroad bumper I won at the HIH9 raffle (A little more than a year after I received it due to a house remodel, two moves, and getting married slowing my wrenching time; still need to wire up the reverse lights and install the trailer wiring)! By far, the most well designed aftermarket equipment I've installed in my almost 25 years of wrenching. Thanks to @benc for his support of HIH every year!
dissentoffroad.com
I also added a Gamiviti @nakman spare receiver behind the spare tire and will use it for bike racks or traction boards bolted to the accessory plate I bought as well. You can see in the first pic that it had no problems clearing the stock wheel. Great product from another longtime HIH supporter!
Spare Receivers — Gamiviti - http://www.gamiviti.com/spare-receivers
Dissent Off-road. Quality Toyota Armor. Explore with Confidence.
Dissent specializes in manufacturing the highest quality off-road armor for Toyota 4runner, Tacoma, Land Cruiser, Lexus LX 470, LX 570 & GX 470. Aluminum & Steel Off-Road Bumpers. Explore with confidence when you equip your vehicle with Dissent Off-road. Tested off-road, Made in the USA.
dissentoffroad.com
I also added a Gamiviti @nakman spare receiver behind the spare tire and will use it for bike racks or traction boards bolted to the accessory plate I bought as well. You can see in the first pic that it had no problems clearing the stock wheel. Great product from another longtime HIH supporter!
Spare Receivers — Gamiviti - http://www.gamiviti.com/spare-receivers
Last edited:
yngmrostrvile
GOLD Star
Valence lifepo4 battery
Valence U27-12XP LiFePO4 | 12V 138AH 1.766 kWh | Lithium Iron Phosphate Battery | eBay
12V | 138AH | 1.766 kWh. 138AH, 1766wh. Valence U27-12XP. Valence U27-12XP Lithium Iron Phosphate Batteries. Communications cables all functional - able to connect to Valence BMS or use adapter to connect to the computer (devices not included).
www.ebay.com
Blue Sea 5025B 6 Circuit Blade Fuse Block with Cover and Negative Bus Bulk
Quality fuse block accepts standard ATC/ATO fuses. Positive distribution bus with #10-32 stud. 6 circuit design. 100 Amp max per block, 30 Amp max per circuit. Includes storage for 2 spare fuses. Snap-in Cover. 3.32"W x 4.9"H x 1.52"D. Bulk version for upfitters/OEMs. Fuses not included.
powerwerx.com
Amazon product ASIN B07RP5B5P7Renogy 50 amp dcdc charger
Amazon product ASIN B07W84SS41Renogy bluetooth module
https://www.amazon.com/dp/B0899932YC?ref=ppx_pop_mob_ap_share
Cable and terminals
Marine Grade Tinned Copper Battery Cable
Marine grade heatshrink from Harbor Freight.
