It's one I made to keep the pups in the back. I made it to anchor at the bottom through the D-rings, the top through the grab handles and under the headrest in the middle.
Cheers,
Scot
What have you done to your 100 Series this week? (97 Viewers)
- Thread starter SHUSH
- Start date
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.
Cheers,
Scot
Getting 315/75/16 's Cooper SST PRO's but paranoid they wont fit. Currently it has 305/70/16 's . so 33 inch to 35 inch I think
Currently has about 2 1/2 inch lift and is a FZJ105R front live axle. So thinking I will be ok for clearance.
Feel free to comment if you have done this already on this setup. 80 series has similar front setup
Here's the difference on a tire size calculator.
285/75-R16 vs 315/75-R16 Tire Comparison - Tire Size Calculator | Tacoma World
315/75-R16 tires are 1.77 inches (45 mm) larger in diameter than 285/75-R16 tires and the speedometer difference is 5.1%
www.tacomaworld.com
Here's the difference on a tire size calculator.
285/75-R16 vs 315/75-R16 Tire Comparison - Tire Size Calculator | Tacoma World
315/75-R16 tires are 1.77 inches (45 mm) larger in diameter than 285/75-R16 tires and the speedometer difference is 5.1%
Cheers for reply. Yeah looked at that , looked at an Australian version of that comparison tool also. Also looked at speedometre differences compared to stock.
Below are pics of the current (older) Cooper SST PRO 305/70/16 's
I made the quick measurements around the tyre and I think I will be fine. If not it will be very close. SPrings in front look to be the only thing to be in the way, but I take it a normal turn would never turn that far anyway,
Works out as 23 mm diameter and 5mm each side width. Even with the 305/70/16 currently bald I think it will be fine. Will add pics to here after its done Tuesday morning. Maybe it will help someone else with similar mod/s going up a size.
Last edited:
audioviking
SILVER Star
I have a single crack on each side. Where did you source the trim? Going through several project during my WFH time.
Direct light and low light effect. Kind of starting to like it a bit.
Since I finished baselining brownie, I finally go time to work on the aesthetics..
Removed the running boards last weekend.
Couldn't stand the mud flaps. Thanks to @LandCruiserPhil for the eliminators..
Before:
After sprayed matte black (Much better!):
Next plans are to get the suspension to par and get some 295 meat...
Removed the running boards last weekend.
Couldn't stand the mud flaps. Thanks to @LandCruiserPhil for the eliminators..
Before:
After sprayed matte black (Much better!):
Next plans are to get the suspension to par and get some 295 meat...
Will do, the rest are still cookin’.More pics against car
wildsmith
SILVER Star
Made a wheel carrier.
mdcoa
SILVER Star
I got mine at McGeorge. Part numbers in my original post—I think they were $20ish ea.
mdcoa
SILVER Star
What’s the pivot point mounted to—I don’t recall anything nearly beefy enough for mounting that under my bumper cover....
wildsmith
SILVER Star
I made a pretty substantial support piece under the bumper cover for the pivot to mount to. It's a tight space to get something rigid enough into.
Installed my Huracan Tailgate Storage Compartment!
Wild! The finished product looks amazing! You should sell this!
Jealous!
I installed a new actuator for the Center Diff as mine had failed. I measured out the front rive play and determined I need new CVS and hub flanges. And I removed the rear spoiler, so I could shift the expedition rack backwards another 2", hopefully to reduce the highway noise from the RTT.
Nothing looks better than a CENTERED spare carrier. Nice and tight to the body I might add.
Hat tip, well done sir.
Best stock/mod swing out option looks hella clean.
You’re gonna love the 315 width aired down on the sand. Post a pic when installed
Can't wait until tommorrow . Might take em down the beach for the pics
Yes! I have a crack in this same trim on either side. Any pointers?! Part #?
