What do you want for your cruiser that you cant not get?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Cable Locker
Tall skinnies
 
Looking for drivers side bench seat hooks (71). I might have to make something as I'm drawing a blank. Funnily enough people like to sell seats whole, and not in parts :)
photo.webp

photo (1).webp
photo.webp
photo (1).webp
 
Cheap, reliable, bolt on, Fuel injection... That delivers exceptional low end performance and economy.:hhmm:

1969 350 w/ 10.25:1 compression and RV cam.:D
 
Pistorman said:
I'm not selling one, I WANT ONE :)

But it should look like this one that was sold two years ago by a fellow mudder.
Click to expand...


Who sold that one? May have been one that I bought. I konow damn hoarder

rgentry said:
I believe that some people purchase the new step, then cut and weld the tabs at the top to mate with the older holes in the rear cross member. What I don't know is if the step itself is of the same width.
Click to expand...


I had planned on installing a later step onto a earlier cruiser. But instead of going to all the work of switching the flanges I filled in the mounting holes and planned on drilling new mounting holes. They would mount in the same holes as the earlier style. Found a couple of earlier step so I gave up the idea. Probablydrill it out to the later style again.
 
merlinridesagain said:
Looking for drivers side bench seat hooks (71). I might have to make something as I'm drawing a blank. Funnily enough people like to sell seats whole, and not in parts :)
View attachment 513285

View attachment 513286
Click to expand...


I got lucky and found one of those in a junk yard. But I plan on using it to convert a 71/72 bench seat with the fixed center section for emission tank to a fold down arm rest that locks upright.
 
Biscuit said:
In stock at $OR Specter Off-Road Land Cruiser Parts - Page 321 Land Cruiser Sliding Rear Windows Emphasis on the $.
Click to expand...

Spector is the only place to get these sliding rear windows for now. ;) Their cost is $410? That seems really high for a slider window.

I have some sources for slider window manufacturing. I will start working on this one if there is enough interest. I think there will be.

I need a little help from all of you to get started. I got rid of my last hard top a few months ago. I dont have one to take measurements. I have looked everywhere online and cant find measurements and when i do, I am getting mixed information. If someone has a side hardtop panel with the glass out that they could take some pictures with a measuring tape showing height and width. This will work for a preliminary work up. I can get a panel that Tackleberry has offered near me, but it might be a week or so. Id like to get on this now. This would be for years 63-76.

Thanks Brothers!

I will post this up in a new thread to track any progress.
 
majojo4 said:
This would be for years 63-76.
Click to expand...
I would have to double check to be sure but the weather stripping and windows changed sizes between the 71 and 72 models years. As for the 77 model and up probably pretty easy to cut the vent window post out and install a slider. I went the other way in that I installed the vent window into a 73 using parts from a 78. The shorter window weather stripping fit fine into the 73 top. The vent window weather stripping was also a perfect fit to the back side.

:cheers:
 
Living in the Past said:
I would have to double check to be sure but the weather stripping and windows changed sizes between the 71 and 72 models years. As for the 77 model and up probably pretty easy to cut the vent window post out and install a slider. I went the other way in that I installed the vent window into a 73 using parts from a 78. The shorter window weather stripping fit fine into the 73 top. The vent window weather stripping was also a perfect fit to the back side.

:cheers:
Click to expand...

Nice thought. Even though the weather stripping/glass size varied, did the hardtop window opening change? Spector is selling the Sliding window advertized for 63-76
 
window pulls for oem soft doors and oem soft door weatherstripping chanells
 
i know some fj25 guys are looking for rear view mirror brackets (the inside cab bracket)...not side mirror arms
 
majojo4 said:
Nice thought. Even though the weather stripping/glass size varied, did the hardtop window opening change? Spector is selling the Sliding window advertized for 63-76
Click to expand...

Those would actually be for mid '65 on ...corrugated tops ended in mid '65, and all corrugated tops had much smaller side windows...very different.
 
he needs 100,000 for his cruiser :)

because.....What do you want for your cruiser that you cant not get? :)
 
Weather stripping for the 74 that fits like OE... OEM is no longer available for both sides.
 
You must log in or register to reply here.

Similar threads

C
  • Question Question
What tools do you keep in your FJ40?
2 3
Replies
42
Views
4K
65swb45
65swb45
Mark Jennings
Do you service your Distributer
2
Replies
22
Views
2K
Pighead
Pighead
msapers
My proposed Dash Layout. What say you?
Replies
5
Views
735
msapers
msapers
miker
What wheels are you using for 37x12.50 tires on a FJ40?
Replies
15
Views
1K
bikersmurf
bikersmurf

Users who are viewing this thread

Total: 1 (members: 0, guests: 1)

Share this page

Back
Top Bottom